Jump to content
  • P1595 Speed Control Solenoid Circuits

       (0 reviews)

    Mopar1973Man

    DTC P1595: SPEED CONTROL SOLENOID CIRCUITS

    1. Turn ignition on with engine off. Using scan tool, actuate speed control vent solenoid and listen for operating sound (click) at speed control servo. Speed control servo is located below driver's side battery tray. See Fig. 59 . If operating sound is heard at speed control servo, go to next step. If operating sound is not heard at speed control servo, go to step 6 .

    2. Ensure ignition is on and speed control vent solenoid is still actuated. Wiggle wiring harness and connectors between speed control servo, brake switch and PCM while checking for interruption of speed control vent solenoid actuation. Brake switch is located near top of brake pedal. PCM is located at passenger's side rear corner of engine compartment. If speed control vent solenoid actuation was not interrupted while wiggling wiring harness and connectors, stop actuation of speed control vent solenoid. Go to next step. If speed control vent solenoid actuation was interrupted while wiggling wiring harness and connectors, stop actuation of speed control vent solenoid. Repair wiring or connectors as necessary. Perform TEST VER-4A .

    3. Ensure ignition is on with engine off. Using scan tool, actuate speed control vacuum solenoid and listen for operating sound (click) at speed control servo. If operating sound is heard at speed control servo, go to next step. If operating sound is not heard at speed control servo, go to step 6 .

    4. Ensure ignition is on and speed control vacuum solenoid is still actuated. Wiggle wiring harness and connectors between speed control servo, brake switch and PCM while checking for interruption of speed control vacuum solenoid actuation. If speed control vacuum solenoid actuation was not interrupted while wiggling wiring harness and connectors, stop actuation of speed control vacuum solenoid. Go to next step. If speed control vacuum solenoid actuation was interrupted while wiggling wiring harness and connectors, stop actuation of speed control vacuum solenoid. Repair wiring or connectors as necessary. Perform TEST VER-4A .

    5. Turn ignition off. Inspect wiring harness and connectors between speed control servo, brake switch and PCM. If no problems exist, test is complete. If any problems exist, repair wiring or connectors as necessary. Perform TEST VER-4A .

    6. Turn ignition off. Disconnect speed control servo connector. Turn ignition on with engine off. Using scan tool, actuate speed control vent or speed control vacuum solenoid. Using 12-volt test light, check for voltage at terminal No. 3 (Dark Blue/Red wire) on speed control servo connector. DO NOT depress brake pedal when checking voltage. If test light illuminates brightly, go to next step. If test light does not illuminate brightly, go to step 12 .

    7. Turn ignition off. Ensure speed control servo connector is still disconnected. Using ohmmeter, check resistance between ground and terminal No. 4 (Black wire) on speed control servo connector. If resistance less than 5 ohms, go to next step. If resistance is 5 ohms or more, repair open on Black wire between speed control servo and ground connection. Ground connection is located on driver's side fender panel. Perform TEST VER-4A .

    8. Ensure ignition is off and speed control servo connector is still disconnected. Disconnect PCM connectors. PCM is located at passenger's side rear corner of engine compartment. Using ohmmeter, check resistance between ground and terminal No. 1 (Tan/Red wire) on speed control servo connector. If resistance is 5 ohms or more, go to next step. If resistance is less than 5 ohms, repair short to ground on Tan/Red wire between speed control servo and PCM. Perform TEST VER-4A .

    9. Ensure speed control servo connector and PCM connectors are still disconnected. Using ohmmeter, check resistance between ground and terminal No. 2 (Light Green/Red wire) on speed control servo connector. If resistance is 5 ohms or more, go to next step. If resistance is less than 5 ohms, repair short to ground on Light Green/Red wire between speed control servo and PCM. Perform TEST VER-4A .

    10. Ensure speed control servo connector and PCM connectors are still disconnected. Using ohmmeter, check resistance between terminal No. 1 (Tan/Red wire) on speed control servo connector and terminal No. 4 (Tan/Red wire) on PCM connector C3. If resistance is less than 5 ohms, go to next step. If resistance 5 ohms or more, repair open on Tan/Red wire between speed control servo and PCM. Perform TEST VER- 4A .

    11. Ensure speed control servo connector and PCM connectors are still disconnected. Using ohmmeter, check resistance between terminal No. 2 (Light Green/Red wire) on speed control servo connector and terminal No. 5 (Light Green/Red wire) on PCM connector C3. If resistance is less than 5 ohms, replace speed control servo. Perform TEST VER-4A . If resistance 5 ohms or more, repair open on Light Green/Red wire between speed control servo and PCM. Perform TEST VER-4A .

    12. Turn ignition off. Ensure speed control servo connector is still disconnected. Using ohmmeter, check resistance between ground and terminal No. 3 (Dark Blue/Red wire) on speed control servo connector. If resistance is 5 ohms or more, go to next step. If resistance is less than 5 ohms, repair short to ground on Dark Blue/Red wire between speed control servo and brake switch. Brake switch is located near top of brake pedal. Perform TEST VER-4A .

    13. Disconnect brake switch connector. Turn ignition on with engine off. Using scan tool, actuate speed control vent solenoid or speed control vacuum solenoid. Using 12-volt test light, check for voltage at terminal No. 3 (Yellow/Red wire) on brake switch connector. If test light illuminates brightly, go to next step. If test light does not illuminate brightly, go to step 16 .

    14. Brake switch adjustment should be checked. Reinstall brake switch connector. To check brake switch adjustment, depress brake pedal. Ensure brakelights come on. Release brake pedal. Ensure brakelights go off. If brake switch is properly adjusted and brakelight operation is as specified, go to next step. If and brakelight operation is not as specified, replace brake switch, as brake switch is nonadjustable and can only be adjusted when NEW brake switch is installed. Perform TEST VER-4A .

    15. Disconnect brake switch connector. Ensure speed control servo connector is still disconnected. Using ohmmeter, check resistance between terminal No. 4 (Dark Blue/Red wire) on brake switch connector and terminal No. 3 (Dark Blue/Red wire) on speed control servo connector. If resistance is less than 5 ohms, replace brake switch. Perform TEST VER-4A . If resistance is 5 ohms or more, repair open on Dark Blue/Red wire between brake switch and speed control servo. Perform TEST VER-4A .

    16. Ensure ignition is off and brake switch connector is still disconnected. Disconnect PCM connectors. PCM is located at passenger's side rear corner of engine compartment. Using ohmmeter, check resistance between terminal No. 3 (Yellow/Red wire) on brake switch connector and terminal No. 11 (Yellow/Red wire) on PCM connector C3. If resistance is less than 5 ohms, replace PCM. Perform TEST VER-4A . If resistance is 5 ohms or more, repair open on Yellow/Red wire between brake switch and PCM. Perform TEST VER-4A


    User Feedback

    There are no reviews to display.


×
×
  • Create New...