Jump to content
Mike Needs Help with Medical Bills Read more... ×
  • Donation Goals

    Mopar1973Man Medical Bills

    If you want to donate to Michael Nelson medical bills. Any fund donated here will be directed toward the medical bills and getting them paid. 


    16%
    $80.00 of $500.00 Donate Now
  • Raffles

  • P0336 Crankshaft Position (CKP) Sensor Signal

       (0 reviews)

    Mopar1973Man

    P0336 CRANKSHAFT POSITION (CKP) SENSOR SIGNAL

    When Monitored and Set Condition:

    When Monitored: With the key on.
    Set Condition: The voltage detected at the Crankshaft position sensor is below a calibrated value.

    POSSIBLE CAUSES

    • CKP SENSOR
    • (G17) SIGNAL CIRCUIT OPEN
    • (K6) 5-VOLT SUPPLY CIRCUIT OPEN
    • (K167) RETURN CIRCUIT OPEN
    • (G17) SIGNAL CIRCUIT SHORTED TO (K167) RETURN CIRCUIT
    • (K6) 5-VOLT SUPPLY CIRCUIT SHORTED TO (K167) RETURN CIRCUIT
    • (G17) SIGNAL CIRCUIT SHORTED TO (K6) 5-VOLT SUPPLY CIRCUIT
    • (G17) SIGNAL CIRCUIT SHORTED TO GROUND
    • (K6) 5-VOLT SUPPLY CIRCUIT SHORTED TO BATTERY NEGATIVE
    • INTERMITTENT CONDITION
    • ECM

    DIAGNOSTIC PROCEDURE

    1. Disconnect the CKP sensor harness connector. Measure the resistance between the (K6) 5-volt supply circuit and the (G17) signal circuit of the sensor harness connector. Is the resistance between 900 and 1100 ohms?
      Yes --> Go To 2
      No --> Replace the CKP sensor. Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL).
    2. Disconnect the ECM harness connectors. Disconnect the CKP sensor harness connector. Check connectors - Clean/repair as necessary. Measure the resistance of the (G17) signal circuit between the ECM harness connector and the CKP sensor harness connector. Is the resistance less than 10 ohms?
      Yes --> Go To 3
      No --> Repair the open (G17) signal circuit. Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL).
    3. Measure the resistance of the (K6) 5-volt supply circuit between the ECM harness connector and the CKP sensor harness connector. Is the resistance less than 10 ohms?
      Yes --> Go To 4
      No --> Repair the open (K6) 5-volt supply circuit. Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL).
    4. Measure the resistance of the (K167) return circuit between the ECM harness connector and the CKP sensor harness connector. Is the resistance less than 10 ohms?
      Yes --> Go To 5
      No --> Repair the open (K167) return circuit. Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL).
    5. Measure the resistance between the (G17) signal circuit and the (K167) return circuit in the sensor connector. Is the resistance greater than 100k Ohms?
      Yes --> Go To 6
      No --> Repair the short circuit or replace the engine harness. Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL).
    6. Measure the resistance between the (K6) 5-volt supply circuit and the (K167) return circuit in the sensor connector. Is the resistance greater than 100k Ohms?
      Yes --> Go To 7
      No --> Repair the short circuit or replace the engine harness. Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL).
    7. Measure the resistance between the (G17) signal circuit and ground. Is the resistance greater than 100k Ohms?
      Yes --> Go To 8
      No --> Repair the short circuit or replace the engine harness. Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL).
    8. Measure the resistance between the (K6) 5-volt supply circuit and ground. Is the resistance greater than 100k Ohms? Yes --> Go To 9
      No --> Repair the short circuit or replace the engine harness. Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL).
    9. Measure the resistance between the (G17) signal circuit and the (K6) 5-volt supply circuit in the sensor connector. Is the resistance greater than 100k Ohms?
      Yes --> Go To 10
      No --> Repair the short circuit or replace the engine harness. Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL).
    10. Reconnect the ECM harness connectors. Ignition On, engine not running. With the DRBIII®, erase DTCs. Connect a jumper wire between the sensor supply circuit and the sensor return circuit in the sensor harness connector. Did DTC P0337 set?
      Yes --> Refer to the SYMPTOM: INTERMITTENT CONDITION Symptom (Diagnostic Procedure). Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL).
      No --> Replace the ECM. Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL).


    User Feedback

    Create an account or sign in to leave a review

    You need to be a member in order to leave a review

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now

    There are no reviews to display.


×