Search the Community
Showing results for tags 'cad'.
Found 10 results
-
Well I've been wanting to install a toggle switch to engage and disengage my CAD for a while now and finally took the time today to tackle the project. It will allow me to use the low range on my transfer case and remain in 2wd. It's very handy when moving trailers around in tight spaces like steep driveways and such in the mountains where I'm primarily working. I used a Clifford MJTV-5 pneumatic toggle switch and 1/4" air brake line. @TFaoro this should work for you as well so you can eng/disengage your CAD.
-
When I use the 4wd the light in the instrument panel has a mind of it's own. I am going into 4wd fine but when i first used it, the light wound not go out when i shifted back to 2wd, until i guess it shook whatever sender it has free (Gumed up?). The other day it didn't come on at all when i was in the snow in 4wd. Does anyone have any fixes or test? Thanks for any help. just want it to work the was it is suspose too.:confused2:
-
99 3/4 ton diesel 4x4,241hdwhen in 4wd i have loud clunking under front of truck.iv'e checked in the diff and both axle u-joints and front bearings.all look good, could it be the front drive shaft u-joints making this noise?any body had trouble with this?thanks in advance
-
Front Axle vacuum diagram/operation
Rogan posted a topic in 2nd Generation Dodge 24 Valve Powertrain
Anyone have a good explanation/diagram on what happens and how, vacuum-wise, with the front axle? which vacuum line (to the axle) does what/when?Thanks! -
OK, Brainiacs, from my last post, I changed the U/L ball joints out last weekend. Once you get the hang of what you're doing, it's not to bad. Well, around Tuesday, I noticed a light blinked on the dash, bottom middle. Didn't know what it was, till I got home and used a flashlight..... 4WD light. I thought maybe, the bulb was going out. So I put it in 4H to take a spin around the property.... the light didn't come on, but it went into 4WD. Today when I left the house, the light started blinking, almost like a strobe light when I was driving. It would go off when I came to a stop, but then when I get to around 35, it starts blinking again, but sometimes it goes out, then starts again. Has anybody had this happen to them, or what did I do. Any answers?
-
Ok guys my question is who is running or had experience with these http://www.4x4posi-lok.com/app_dodge.html??? If you are running one whats the install like, op's like, what does the install look like in the cab, etc.? for the price it doesnt look too bad but i would like to hear from you guys.
-
I need a good place to order a axle disconnect shift fork. dealer wants 96$. I would like to see if I a can find it cheaper, but want to make sure I get the right one too. -
Here Mike, make an article around this video Fine I will later.
-
Anyone know how to test the vaccuum for the CAD 4x4 axle. Specifically - not sure if I have a problem with the CAD itself - or vacuum isn't correct on the two lines (red and black). Is there an easy way to test a) There is vacummb) Its the correct vaccum pressure I suspect my main issue is the actuator/thing on top of the transfer case - as it was pretty dirty when I reinstalled my tranny - so I cleaned out as best I could. Just want to know what I could do to test each component - before I go out and buy a posilok. thanks
-
Hello,My 4 wheel drive will not engage I noticed it Saturday while helping Brother in law move.I recently had it in for repair of cam cover gasket wondering if there was somethingthat might have been disconnected during the repair causing this. I have a 2500 2001 sport quad cab.Thanks in advanceDavid
