Jump to content
  • Welcome To Mopar1973Man.Com

    We can see that your guest and been lurking about. When you register on the Mopar1973Man.Com site you'll be able to interact with all the other members. This is the most friendliest Cummins forum you'll ever join. Take the time right now and  REGISTER  on the Mopar1973Man.Com this will open up many more options and functions on the website. Everyone is very friendly and helpful just ask questions and everyone will help you out the best they can. 

Jerm2554

Need Quadzilla adrenaline tuning help

Recommended Posts

I recently bought a Quadzilla Adrenaline 4k v2 programmer and am having some tuning issues I cant seem to figure out. I only use the truck for sled pulling and do not drive it on the road. The main issue I'm having is at the end of the pull it will stay revved up after i let off the pedal for a short time and then come down to an idle. Any help would greatly be appreciated!!

Share this post


Link to post
Share on other sites

how long does it stay revved up?  the 4k boxes do that as the ecm is freaking out and not sending data updates for what TPS is at etc.

Share this post


Link to post
Share on other sites

I would say 7 or 8 sec or so give or take. I'm new to tuning myself and wasnt sure if I have something set wrong or what not. I've messed with just about every setting on here lol.

Share this post


Link to post
Share on other sites

Power level:9

RPM LIMIT:4000

VALET MODE:25%

MAX FUEL STRETCH :5800

TPS MAX: 75%

TPS MIN: 15%

MIn. Pump tap fueling: 10%

Pump low boost scale: 5 psi

Boost scaling: 20 psi

Fuel load timing: 0° 

Low psi timing reduct: 3°

Timing reduct scaling: 100%

Light throttle timing adv: 0°

Light throttle limit: 0°

1500RPM: 16°

2000RPM: 19°

2500RPM: 21°

3000RPM: 23°

3500RPM: 25°

4000RPM: 26°

MAX: 27°

0PSI:110

1PSI:111

2PSI:112

3PSI:113

4PSI:114

5PSI:115

6PSI:116

7PSI:117

8PSI:118

9PSI:119

10PSI:120

11PSI:122

12PSI:123

13PSI:125

14PSI:128

15PSI:131

16PSI:134

18PSI:137

20PSI:140

22PSI:142

24PSI:144

26PSI:146

28PSI:148

30+PSI:150

 

This is the last tune I have ran.

 

Share this post


Link to post
Share on other sites

First thing I see is your timing is really low

 

try

 

1500RPM: 16°

2000RPM: 19°

2500RPM: 25°

3000RPM: 29°

3500RPM: 32°

4000RPM: 32

MAX: 32°

 

Turn stretch down to 5000 and try again

 

TPS max to %100

boost scaling 40

Share this post


Link to post
Share on other sites

Ok sounds good, i had a feeling timing was on the low side!.

I will give it a try tomorrow evening and let you know how I make out! Thanks for the help!

The quadzilla will only allow me to go to 30° not 32°

Share this post


Link to post
Share on other sites

Meh same difference, the mechanical limit of the pump is somewhere aorund 30* any ways.  

 

 

IF it still hang revs drop wiretap more, you have big injectors you dont need to max out stretch

Share this post


Link to post
Share on other sites

I tried your tune out last night! I have no more reving problem and the truck seems to run the best it ever ran! Thanks so much for the help!!!!

  • Like 1

Share this post


Link to post
Share on other sites

I was going over my data log from Friday's run. On the wire tap % I'm at 90%. Is there a reason why I'm only getting 90% and not 100%? 

Share this post


Link to post
Share on other sites
Posted (edited)

Are you at %100 throttle?  How about boost?  Rpms?

 

Many things play into how much wiretap.  As you noticed too much wiretap can cause issues.  

 

Are you unhappy with somethinng other than seeing %90 rather than %100?  Just because you are only running 90% doesnt really mean you are lacking anything.   

 

One could say since you are only using 5000 for fuel stretch you are only using %75 wiretap.....  

 

 

Edited by Me78569

Share this post


Link to post
Share on other sites

I'm at 100% throttle,51psi boost and 3800rpm.

I am not unhappy with it, I was just courious as to the 90% was all lol

Share this post


Link to post
Share on other sites

If I remember hte wiretap map you don't get %100 above ~3000 rpm.  if you wanted to see %100 you would need to be over 50 psi at ~2200 rpm. 

 

 

 

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.




×
×
  • Create New...