P0335 CRANKSHAFT POSITION (CKP) LOST

When Monitored and Set Condition:

When Monitored: While the engine is running.
Set Condition: The ECM no longer detects a signal from the Crankshaft Position Sensor.

POSSIBLE CAUSES

• OTHER DTCS
• P0337 PRESENT
• CKP SENSOR
• VISUAL DAMAGE
• (G17) SIGNAL CIRCUIT OPEN
• (K6) 5-VOLT SUPPLY CIRCUIT OPEN
• (K167) RETURN CIRCUIT OPEN
• (G17) SIGNAL CIRCUIT SHORTED TO (K167) RETURN CIRCUIT
• (K6) 5-VOLT SUPPLY CIRCUIT SHORTED TO (K167) RETURN CIRCUIT
• (G17) SIGNAL CIRCUIT SHORTED TO (K6) 5-VOLT SUPPLY CIRCUIT
• (G17) SIGNAL CIRCUIT SHORTED TO GROUND
• (K6) 5-VOLT SUPPLY CIRCUIT SHORTED TO BATTERY NEGATIVE
• INTERMITTENT CONDITION
• ECM

DIAGNOSTIC PROCEDURE

1. With the DRBIII®, read DTCs. Is DTC P2146 and/or P2149 present?
   Yes --> Repair other DTCs. Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL).
   No --> Go To 2
2. With the DRBIII®, read DTCs. Is P0337 present?
   Yes --> Repair P0337 first. Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL).
   No --> Go To 3
3. Visually inspect the sensor, engine belt, sensor connector, and the ECM connector. Is there any damage?
   Yes --> Repair or replace the sensor, engine belt, harness, or the ECM Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL).
   No --> Go To 4
4. Disconnect the CKP sensor harness connector. Check connectors - Clean/repair as necessary. Measure the resistance between the (K6) 5-volt supply circuit and the (G17) signal circuit of the sensor harness connector. Is the resistance between 900 and 1100 ohms?
   Yes --> Go To 5
   No --> Replace the CKP sensor. Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL).
5. Disconnect the ECM harness connectors. Disconnect the CKP sensor harness connector. Check connectors - Clean/repair as necessary. Measure the resistance of the (G17) signal circuit between the ECM harness connector and the CKP sensor harness connector. Is the resistance less than 10 ohms?
   Yes --> Go To 6
   No --> Repair the open (G17) signal circuit. Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL).
6. Measure the resistance of the (K6) 5-volt supply circuit between the ECM harness connector and the CKP sensor harness connector. Is the resistance less than 10 ohms?
   Yes --> Go To 7
   No --> Repair the open (K6) 5-volt supply circuit. Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL).
7. Measure the resistance of the (K167) return circuit between the ECM harness connector and the CKP sensor harness connector. Is the resistance less than 10 ohms?
   Yes --> Go To 8
   No --> Repair the open (K167) return circuit. Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL).
8. Measure the resistance between the (G17) signal circuit and the (K167) return circuit in the sensor connector. Is the resistance greater than 100k Ohms?
   Yes --> Go To 9
   No --> Repair the short circuit or replace the engine harness. Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL).
9. Measure the resistance between the (K6) 5-volt supply circuit and the (K167) return circuit in the sensor connector. Is the resistance greater than 100k Ohms?
   Yes --> Go To 10
   No --> Repair the short circuit or replace the engine harness. Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL).
10. Measure the resistance between the (G17) signal circuit and ground. Is the resistance greater than 100k Ohms?
    Yes --> Go To 11
    No --> Repair the short circuit or replace the engine harness. Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL).
11. Measure the resistance between the (K6) 5-volt supply circuit and ground. Is the resistance greater than 100k Ohms?
    Yes --> Go To 12
    No --> Repair the short circuit or replace the engine harness. Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL).
12. Measure the resistance between the (G17) signal circuit and the (K6) 5-volt supply circuit in the sensor connector. Is the resistance greater than 100k Ohms?
    Yes --> Go To 13
    No --> Repair the short circuit or replace the engine harness. Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL).
13. Reconnect the ECM harness connectors. Ignition on, engine not running. With the DRBIII®, erase DTCs. Connect a jumper wire between the sensor supply circuit and the sensor return circuit in the sensor harness connector. Did DTC P0337 set?
    Yes --> Refer to the SYMPTOM: INTERMITTENT CONDITION Symptom (Diagnostic Procedure). Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL).
    No --> Replace the ECM. Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL).