2nd Generation Dodge 24 Valve Powertrain

As the title says next week I will be out in Utah for 2 weeks and plan on visiting the folks at Edge Products to drop off my Drag Comp for repair. I plan on spending as much time as I can with them and one of their product specialists. So for all of you I am starting this thread to compile any questions, suggestion, concerns, you might have to pass to them and gain insight to their future product to pass on to you. Please Respond here with your lists by Tuesday Nov 9th am so I can get it to them and I’ll respond back after my Visit. Thanks JG

O.K. I TO had been struggling with this stalling issue..but.. about 2-months ago i thought i had fixed it buy replacing some ground connections and a TIMBP APPPS...Wrong....yestarday it done it again..thing is..it is random..and unlike SASQCH & JOHNFAK ..MINE does not seem to do it when it cold...only does it after its warmed up and has been ran a few miles...mine too will pull down rpms real low at times but does not stall but it almost does..:banghead: I am curious..has anyone had this issue that is running stock injectors and stock SO VP pump??? Richie

Hello everybody this is Randy from Indiana, sorry it took so long to get these results but our labs busy season had started and i had to slip it in when I could. So i tested a Kendall GT-1 two cylce oil bought from Hires auto parts and compared it to our TDR-S product. The results are as follows: I treated the fuel with one once of two-cycle oil per ten gallons of diesel fuel or 700ppm's per gallon. The base fuel had a HFRR of 520um which is ASTM spec The fuel with the two-cycle oil had HFRR of 470um. The fuel treated with the TDR-S had a HFRR of 425umSo the answer to some of your questions is yes the two-cycle oil does lubricate your engines, but if you were …

She runs like you anit never seen, boys I am going to be hitting 19 mpg I just know it for a 9800 lbs truck. It runs so smooth you dont even know it's running, sounds like a electric car it's so quiet. 2 Years of misery man finally over, next I be hittin the rollers LOL.Sorry for all the excitement, I just cant get over it's finally done. 1 Million miles here I come. Well only 750k left to go.

Ok Gang... I know we got a lot of knowledgeable guys with a few extra part in the garage and a bit of extra time here and there... I got a wonderful member that is need of help here. Russ is in a pinch with the economy going down and with his disabilities it hard for him to do the work himself. So I'm asking all the members of the site to please look at this message below and see if you can help Russ out... What I'm asking is if there is any member on the east coast near Rhodes Island that could give Russ a hand by either donating time or possibly parts to his cause.

Here ya go, you think it had a problem? And check out the eng. hoist. #1 & 6 where black.

Can anybody give me filter numbers (fleet guard, etc) for a FASS 150? I've got a friend that needs some and I thought I'd seen a number cross-over somewhere but I can only find it for the Airdog pumps.

Ok so i have a problem with my raptor fuel pump.I've had it for about a year and when i got it i got 3/8 lines. and i would see about a 5-7 psi drop with ds2.Now i just upgraded to all 1/2 lines including from ff to ip and a draw straw 5 and at 30psi fp i can get it down to about 4.(I know 30 is high but i set it there to see how low i could get it with out running to 0)I replaced the ff and checked/tightened all fittings.What could it be?Its driving me crazy.The only thing i can possibly think it could be is the "Straw" at the bottom of the module. When i installed it it seemed like it was a little close to the bottom with not much of a "Slash cut" to it.Could that being…

http://mopar.mopar1973man.com/cummins/2ndgen24v/valve-adj/valve-adj.htm just got done running the valves.#6int and exhaust valves were out alittle.got them all adjusted in time before winter time gets here.:thumbup2:fired it up and the little tick tick was gone:thumbup2:

getting ready to update fuel lift pump .....probly a raptor..was going to put in a fuel press gauge and noticed the elec I was looking at is bout 30 dollars more.....any thoughts on which one to go with and why...was looking at isspro....I imagine the electric is a little less of a pain to install...is it as accurate?...

My truck was running ok for about 160 miles and then it acted like it didnt have any power for a few minutes but then it was ok again. I checked the codes when I got home and I got 234 and 236, Ive had them before, the manual describes them as "problem detected in turbocharger wastegate" I checked the wastegate actuator and you can push the rod to open the wastegate with a screwdriver, it takes a some pressure but it does seem to open, and I hooked air to it and it opened at around 25psi, and it doesnt seem like the acuator is leaking or anything. Should it open at a lower psi? Im also getting a 382 code. The heater works when you plug it in, and the truck doesnt have any…

Hey Gang... I've got a member here that is looking for information on ECM shops/rebuilders that could possibly test and repair a ECM. I'm sure there was a few threads out here but I'm looking for currently good shops... Yeah I know there is a few of "Bad" shops too. Lets here it guys... Oh... If you want you can post you information to... http://forum.mopar1973man.com/showthread.php/2897-Help-911-Diesel-Down?p=21913#post21913

After looken at cummins2001’s post hotw to get lower EGT’S http://forum.mopar1973man.com/showthread.php/2867-How-to-get-lower-egt-s I have NO problem with EGT’s I can’t get them past 800 even towing. As my other post I want to get a little more gitty up. And was wondering what Trubo I have? After looking and looking I could not find a tag I did find some numbers on the houseing Holset then there was a small 50 after that One location said BK 2400 Next said 3593085 I looked throught both fourms to find infor on this and Googled it for number or pictures and found nothing one sight had the numbers but no information Her are some pictures of it. i have…

I got my tranny rebuilt about a month ago and the tc lockup has been acting up. It sometimes locks and sometimes it feels like it is partly locked:cry: I took it back to the tranny shop for a checkup and he's pretty puzzled by what it is doing. I did play around with a mystery switch and I'm wondering if there's any way that I could have messed something up. In the process of this I had the center plug on the powertrain module off to tap into the black/orange wire and I broke off the pin on the wire from the trans temp sensor. I kind of got it back together but could a bad connection on that circuit have caused a problem like I have? I'm sure hoping not cuz I want t…

It appears my lift pump is dead. I pulled the relay and jumpered the correct connectors, heard contacts click in, but no pump running. I'm on a budget (= low funding) and would like a decent quality unit that can bolt in, no huge modifications to my fuel system. Also, a recommended fuel pressure gauge installation set up would be appreciated.

Hi Guys:For some time now my truck shudders with my QUAD XZT+ programmer. Someone told me this problem was fixed at the factory and that it was available in the download section of Quad's webpage which I did, but the problem is still there especially at lower speeds. Any ideas?Thanks,Arcwelder

Just so you know, carry a box with you just in case, 30 amp fuse is what it took to chew what ever it was that bound up in rotor. I know that sounds bad but what are you going to do when you setting on the side of highway about to get creamed from cars doing 90. Oh yea, I can call MoparMan at 7:00am lol, he says he been up, but I dont know sounded a little dry like he been snoring. lol Just ribin ya buddy, thanks for being there.Ok back to pulling head, letting head cool down before I dive in. Let ya know what I find.Anybody know what the Wix numbers would be?

I was in Napa this morning and they have Premium Blue on sale for $9.99. I don't need any (bought my supply when Oreileys had it on sale). Don't know when it goes off sale. But at that price, I figured I would pass on the info to everyone!

First off let’s start off with saying I’m glad I found your site!!! Great Job and keep up the great work!!! I have been in the Cummins thing for many years, I use to be the admin on the old SETDR site if some of you remember. That site is what kicked off the Diesel Garage and Comp Diesel sites. When SETDR died I kinda laid back and focused on other things in life. I have an 01 Dodge Cummins ( Big Red )with DD4’s, 5” exhaust, hx35 w/boost elbow, Edge Drag Comp, all the gauges, Holley blue pusher pump ( which I started the installation craze) and a full blown Sun Coast Comp Tranny w/triple lock Tq Convertor, So she’s pretty stout and build to my likeing. Last dyn…

ok need some help here please ......I replaced the clutch and flywheel this past april on my beast ......put in a south bend ....and everything went great until yesterday ....now the truck acts as if the throw out bearing is not completly disengaging the clutch ...ie synchros raking ....stick hard to push into various gears especially 3 rd and reverse.....any ideas other than tearing the whole tranny back out?