2nd Generation Dodge 24 Valve Powertrain

How much would a nv5600 2wd with 170k be worth?

I have a 4x4 truck with a 2wd nv5600. What all do i need to install the transfer case?

I can't imagine this is a common problem but I thought I would share my story. I developed a driveline vibration at cruising speed so on my first day off I pulled it in the garage and sure enough the U joint by the rear axle was bad. When I checked the other joint and it was fine, but I happened to push up on the driveshaft and when I did the whole transfer case moved up and down with it! Upon further inspection two studs that hold the t-case to the trans were gone and all but one were backed way out. Also because the one stud was tight the t-case pivoted off of it and put a pretty good crack in my trans tailhousing. It's not leaking and I got everything tightened up with…

My transmission has lived ALOT longer than it should under my foot with the comp on and up. I drove it heavily on 5X5 for several years before learning the possible weakness of the tranny . I did buy it used and the comp was on it when i bought it but that was all for mods when purchased. just wondering if there is any way i can find out if there was any performance upgrades done without me having to tear it apart completely? i did pull the dust cover which didnt tell me squat and the torque converter does engage in third regardless if the OD is on or not....6 changes in rpm speed through 4 gears (TC engage in 3rd, unlock, shift to OD, reengage). i just h ope somebod…

I has issue with fuel pressure that I had been seen normal it would be about 20 psi but now it had dropped to 12 to 15 psi even changes fuel filter and adjust te regulation. It don't help..Should I contact the air dog company and see what to do? Or time to upgrade to airdog 100 with two filters??

Can you get a G56 tranny to fit into an 01 3500? If so, how labor intensive & expensive is it?

A few days ago I posted that I was hearing a 'rumbling' sound coming from my truck after starting off slowly, after the first start in the morning. A buddy of mine walked beside the truck the other morning when I left from work, and told me it was coming from the front of the engine compartment. I had already determined that the wheels, bearings, brakes were normal. I looked at the belt on my fuel boss, and it was very loose (the instructions for the fuel boss state not to have it too tight). Anyway, it was loose to the point where I could almost slip it off the pulleys. I got to thinking that maybe in the morning when the belt is stiff, it might be jumping the cogs on th…

Just installed my assassin lift pump and draw straw and I am only getting a slow stream of fuel from the pump.Draw straw was installed by drilling a hole in top of the in-tank fuel module. Drilled two holes in the bottom of the fuel module as stated in the instructions. Ran the draw straw through the top and bottom hole so it would be sitting on the bottom of the tank inside the screened cap and trimmed the straw so it would be as close to the bottom as possible. Ran new hose from draw straw up to the pump, then from the pump back to a T with the regulator. At the T, the t'd hose heads up to the stock fuel filter and the back side of the T returns to the tank where I c…

So in the efftot to elimanate issue's in my tranny before I put on my Master/Slave Clyinder. I took the time today to check the fluid level on the side which seemed almost full. then i took off the shifter and what level should the fluid be at cause it looked about 10 quart's low lol Cause i could see way down there is it suppose to be all the way up to the shifter base?? Cause I have no idea i put a quart in it and i couldn't even tell i had put any in it. So any info would be great

Started truck today abs and air bag lights are on also ac blower motor would not come on. Started down road blower motor came on and lights went out. Started truck after work same thing no codes anybody had this problem? Thanks ed

I have had it on my truck now for about 3.5 months now it was at 15psi idle and 22 wot now my idle psi has dropped to 12 but wot is still the same.Will a dirty filter cause this I have not checked it yet but will tomorrow.I changed the filter when I installed the pump I would say that I have about 4000 miles on it.What else would cause this. THANKS

i was just wandering when you guys rebuild your engines what brand of kits do you use and can any machine shop do the work or is this something you have to make sure they know what their doing? how many of you guys do your own rebuilding, is it pretty easy or a thing a pro should do. i have rebuilt gas engines but never a diesel .

P0460 P1595 P1693 fuel lever didn't work in two years cruise stopped working over 6 + month ago fuel pressure is 15 at idle and 12-14 at cruise and maybe 12 at WOT Very hard start daily changed both fuel filters one on engine and the small one pre my lift pump nothing changed I ran out of fuel 3-4 weeks ago and had to open up the injectors to get the air out and truck was fine for a week or so after that then the hard starting problem started I reset the APPS a couple of times and does not help at all

Been driving about a year after the 0216 code came up. It never came up again till a few days ago so I increased fuel pressure to 21-22 from 18 and throwing 2 quarts of 2 cycle with every fill up to help the VP.I have a significant increase in miles hauling the same heavy camper on the same almost exact 3 day long road trip sometimes going 3 times a year.. It's showing a little over a 1 mile per gallon increase to 15.3 from just under 14.:think:I thought the vp should give bad miles when the timing piston starts to wear (0216 error code), but there's no white smoke and no hard starts. runs really good.

This will be a little difficult to describe. When I first get the truck rolling in the morning, I'm hearing a rubbing sound which sounds somewhat rotational, in that it is not constant. It seems to be coming left front. It started a few weeks ago after I changed my crankshaft position sensor, where the only thing I had done was remove the started and reinstall. I have not lifted front end up yet to check wheels, but this noise stops after a few hundred feet, and seems to be only when the truck is not warmed up. If you have any tips please let me know so I can start checking into some things. The starter is brand new rebuild as of yesterday (warrantied one went out yesterd…

Performace Diesel Parts + New Toyota Offering Sale Ends August 31st 2013 Diesel Auto Power is proud to announce that we stock Extreme Head Studs for Dodge, Ford 6.0L and Chevy. Extreme Studs are made from a fine grain, hi-strength - 240k tensile tool steel H13 specifically designed for heavy duty, hi-shock applications (DIESELS). Compare to other studs that sell near $1000. Prices Start at $610 Extreme Studs ------------------------------------------------------------ DODGE CUMMINS ------------------------------------------------------------ Diesel Auto Power offers a full line of replacement and performance injectors fo…

I would like to add the fuel filter as try keep debris away from raptor pump(raptor 100) but I has research and not see what is correct way for me to get a part kit to do on my 2002 dodge ram 3500 cummins as 2wd dually. Also I had noticed the my raptor 100 would not increase te pressure even I did changed the fuel filter at stock canister that did increased from 15psi to 21 but now it went back to 14psi after few weeks driving. I had not get chance to pop the line off at raptor 100 to see at screen to see if plugging up? I had put my cummins into my garage and stay inside for few weeks as had not get time to look at it. Also do I should just upgrade for two filters with…

Coming home from my trip to Texas last week and I see my isspro mechanical water temperature gauge setting about 215* but the gauge in my cluster and my ScangaugeII both reading 188-190. I check my gauges periodically when im driving my truck so I know it was not doing it very long. We stopped to run through the Chik-fil-a drive through and after about 10 minutes or so being back on the road I noticed it. I was running 80 so I backed off down to 70 and it came down a little, maybe 210 or so. I kept a hawks eye on it for the next 10-15 minutes and it just dropped to 195 or so like normal. I watched it the rest of the trip and since but it has not come out of the normal ran…

I have a P0122 TPS code on my 99 Cummins that I cannot get my scanner to clear. When I read the codes it was listed 4 times - twice for confirmed and twice for pending. I told it to clear all codes and I still have one confirmed and one pending remaining. I've tried several times but it won't clear. Any ideas would me helpful. - - - Updated - - - My reader is an ACTRON 9575.

2002 3500 dually 6 speed 200k. Bought this truck late spring, finally getting around to fixing things. Needs new rear rotors. Went to take the rear wheels off, passenger side came off fine. However the Drivers side inner wheel is stuck solid! Looking like some rust in there where the wheel mates against the hub. Dammit! :banghead: I tried everything, doused it with WD40, beat the tire (not the rim) with a hammer, won't budge. Kicked things up a notch and took the truck off jack stands & put the weight of the truck on the wheel & drove it back & forth in my concrete driveway. Nothing! Chirpped and spun the tires on the driveway. Still won't budge! (At lea…