2nd Generation Dodge Reliability / Performance

anyone put a smoke switch in with a quadzilla xzt? i tired but couldn't get it to work properly, a picture of the wires would be helpful thanks! -the truck is a 01'

I'm adding a fuel pressure gauge. Other gauges already in "A" pillar are trans, boost and egt. Since 2005. All the light wires are from one place (not sure yet from where). But wire sure looks real small to me. Basic Question on wiring... To make sure I'm ok on this or any wire project...add up how much elec going to be going through and then select wire size based on how much going thru wire?

So I was fortunate enough to be given a set of Bully Dog 100hp injectors by a fine fellow a few weeks ago. He did a turbo swap and the mechanic convinced him he needed to get new injectors. He replaced them and has since sold the truck, still retaining the old injectors and a factory set also, so he donated them to me. Knowing Bully dog has been out of the production biz of injectors for a while I promptly made a call to DAP. I spoke with Dallas to which he provided me some great information and service. I sent them to DAP (arrived on Friday) to be tested and verified. They are a traditional Bosch body which appears to be in good shape so DAP is going to test and…

im leakin oil real bad on my driver side i cant sure where its comin from but it kinda looks like its commin from the governors in the back of the pump but its from where my AFC housin starts to the back of the motor but i was thinkin it could be CCV because did the timmin and it was retarted 4 or 5degrees and when i did the milage it had 205,000miles on it but anyone havin the same problem or ideas

View Advert 2001 Quadzilla XZT+ Has the standard tunes on it right now. Purchased this spring (2019) to replace my Van Aaken box that had a failure in the harness. Found a replacement harness and no longer have a need for this box. Was installed in the cab under the dash so it’s never gotten wet or full of dirt, harness has no rub spots or any other damage on it. Three option selector switch is with it as well as all the documentation. Make me a reasonable offer. Willing to drive it down to Utah to have a different tune package put on it if you want as well. Thanks! Advertiser TJH …

Vehicle Nickname: Aaron Kelley Date Added To The Garage: 2021-07-24 Garage Link: Aaron Kelley

Vehicle Nickname: Problem Child Date Added To The Garage: 2021-12-31 Garage Link: Problem Child

This is a small improvement over the stock bumper, I am thinking that if I hit a deer out here at least my truck will not be hurt. It did lower the front end down a little, not sure if I want to get a leveling kit, readjust the headlights or just build a stout rear bumper to compensate? It still has a few minor things that needs to be done to it, not too bad for a home built bumper and at least it is on.

Vehicle Nickname: Sheneeda Date Added To The Garage: 2022-12-05 Garage Link: Sheneeda

Vehicle Nickname: Cole Date Added To The Garage: 2022-01-02 Garage Link: Cole

Vehicle Nickname: Andrew capitan Date Added To The Garage: 2022-12-07 Garage Link: Andrew capitan

Vehicle Nickname: Midna Date Added To The Garage: 2021-03-17 Garage Link: Midna

1999 Dodge Ram 2500 4x4 w/heavy package Auto Build Date 9/98 ordered on 10/98 received 1/99 custom ordered Black on Black with Leather/power seats, wood grain trim, Sun Roof, and Heavy/Towing package Glow Shift Guages - EGT, Boost, Trans Temp current mileage - 196013 Engine- 5.9 ISB 53 block Edge Comp Smarty S-03 DAP 100hp sticks ARP studs HE351cw - latest addition PDI manifold Diamond Eye 4" exhaust Trans- I'm on the 3rd trans... 1st one went out at 56000 6/02 - Factory replacement installed 2nd failed at 154K and rebuilt with Suncoast Stage 3 48re guts - Thanks to Ernie at Suncoast NV271 T-case Dana 60 up front Dana 80 in b…

I penned this article, If you guys have remans and they are working good let me know so I can add them into the article.

Vehicle Nickname: Mike Date Added To The Garage: 2022-06-17 Garage Link: Mike

Vehicle Nickname: Cumminsman87 Date Added To The Garage: 2022-12-11 Garage Link: Cumminsman87

Body [*]Dodge Ram 2500 [*]Long Box [*]Quad Cab [*]MOD - Custom Fog Lamps [*]MOD - Tinted Windows (5% Rear Windows 25% on side windows) [*]MOD - Custom Backup Lights [*]MOD - Frantz Filter [*]MOD - Custom High Idle Engine / Transmission [*]I6 5.9L Cummins Diesel Engine [*]NV4500 Manual Transmission (5 Speed) [*]4 Wheel Drive [*]3.55:1 Gear Ratio [*]Non-CAD Front Axle [*]MOD - AirDog 150 [*]MOD - Custom Crankcase Vent [*]MOD - Edge Comp [*]MOD - Exhaust Brake [*]MOD - Straight Pipe Exhaust [*]MOD - RV275 Injectors [*]MOD - Southbend Clutch Vehicle Labels Interior [*]MOD - Kenwood MP3 S…

There is several ways of getting a boost gauge hooked up. I took the easiest way. I got a 3/4" to 1/2" steel bushing. Then used a 1/2" to 1/8" brass bushing. There is a pipe plug right next to the fuel filter. There is several stories about how to do you pyrometer probe. I'm going to explain my method. I center punched the manifold on the rear port where I wanted to drill my hole. I greased my drill bit and drilled slowly with a shop vacuum next to the bit. After drilling I used both a magnetic screwdriver and a Q-tip to pick up any metal chips. Then I greased my tap and tapped my hole. I checked the manifold again in the same way as above. Then install your probe as …

1997 Dodge Ram 2500 12V Cummins Turbo Diesel P7100 13.5* Timing No AFC No Plate 5" Exhaust with Semi Muffler (see through) Exiting in Front of Back Tire Custom Boost Regulator (35PSI) BHAF [*]5 Batteries (5240 CA) [*]Grid Heater Relay On/Off Switch [*]Custom Center Console [*]Front Air Dam [*]Added (Floor Mounted): Boost--Pyrometer--Water Temperature [*]Always On-Power Windows (Jumper Mod) [*]Brush Guard [*]Aluminum Diamond Plate Toolbox [*]Trailer Brake Controller [*]Power/Remote Door Locks [*]Power Seats [*]Power Mirrors [*]Auto Dimming Rear View [*]Overhead Outdoor Temperature [*]245/75/16 [*]Hankook Dynapro Tires (Back 2) [*]Michelin L…