Jump to content
Mopar1973Man.Com LLC

  • Welcome To Mopar1973Man.Com LLC

    We are a privately owned support forum for the Dodge Ram Cummins Diesels. All information is free to read for everyone. To interact or ask questions you must have a subscription plan to enable all other features beyond reading. Please go over to the Subscription Page and pick out a plan that fits you best. At any time you wish to cancel the subscription please go back over to the Subscription Page and hit the Cancel button and your subscription will be stopped. All subscriptions are auto-renewing. 

Edge EZ

Blueox01
 Share

Recommended Posts

Blueox01

Blueox01

Posted
  • Author
Posted

Check the ground on it too.:thumb1:

Think i found problem,this plugs into MAP and routes through edge unit and Map to ECM Plug connects to edge(thats what must advance timing/fool boost code) other plug(not shown) connects to data link from harness to supply power.One wire between MAP plug to MAP to Edge has no continuity:pray:this is the problem.[ATTACH=CONFIG]2509[/ATTACH]
Link to comment
Share on other sites
Blueox01

Blueox01

Posted
  • Author
Posted

does it have a removeable end plate like the edge juice? if so there are some led lights behind that, those will tell you if something is wrong with the unit or somewhere else.

It does but only has jumpers to change power setting,no LED lights. actually plugged my Hypertech back after disconnecting the Edge,seat of pants not much difference.I had run original injectors to 780k replaced with some RV275 and plugged in the Edge(after deprogramming the Hypertech back to stock)but really don't feel a big difference.:shrug:
Link to comment
Share on other sites
retirednak

retirednak

Posted
Posted

I had an EZ Edge for a while. If it has the removable pins for power adjustments,look for a loose plastic piece behind the cover of the unit.(2 screws) I moved the plastic do-da's depending when I towed and what not. I had to spread the pins a tad so the plastic do da's held firm. I used curved pliers to spread the pins. Since I have an '03,I didn't have a power wire nor ground to hood up. If you need instructions,you can go to Edge.com and download there,they also have helpful tech dept to answer any question.

PM me if anybody is interested in an Edge Mileage Max.

  • Like 1
Link to comment
Share on other sites
Heavyd1980

Heavyd1980

Posted
Posted

Think i found problem,this plugs into MAP and routes through edge unit and Map to ECM Plug connects to edge(thats what must advance timing/fool boost code) other plug(not shown) connects to data link from harness to supply power.One wire between MAP plug to MAP to Edge has no continuity:pray:this is the problem.[ATTACH=CONFIG]2509[/ATTACH]

Well it sounds like your onto something now! good luck man!
Link to comment
Share on other sites
Blueox01

Blueox01

Posted
  • Author
Posted

Well it sounds like your onto something now! good luck man!

Took off shrink wrap,that wire goes back into unit:cry:Edge e-mailed me back to try different jumper settings to narrow it down.Probly have to send it in,then buy a new one at discounted price.Try to milk them for the best deal through:evilgrin:,use the Hypertech is just as good ploy(which seat of pants it is),hope nobody on here works for them:whistle:
Link to comment
Share on other sites
Heavyd1980

Heavyd1980

Posted
Posted

Took off shrink wrap,that wire goes back into unit:cry:Edge e-mailed me back to try different jumper settings to narrow it down.Probly have to send it in,then buy a new one at discounted price.Try to milk them for the best deal through:evilgrin:,use the Hypertech is just as good ploy(which seat of pants it is),hope nobody on here works for them:whistle:

I would suggest talking to Mark Hayward over at Edge he is a great guy and he helped me out big time when the turbo timer went out in my juice.
  • Like 1
Link to comment
Share on other sites
  • 2 weeks later...
Blueox01

Blueox01

Posted
  • Author
Posted

does it have a removeable end plate like the edge juice? if so there are some led lights behind that, those will tell you if something is wrong with the unit or somewhere else.

Does'nt have any LEDS just a jumper to switch.But i did finally get around to testing the data connector for Voltage and had none,futher inspection found broken wire.Sure going to be a pain to get a short piece of wire soldiered on in that location:mad:,finding a pin should be no problem.
Link to comment
Share on other sites
JOHNFAK

JOHNFAK

Posted
Posted

I had run original injectors to 780k replaced with some RV275 and plugged in the Edge(after deprogramming the Hypertech back to stock)but really don't feel a big difference.:shrug:

I'll be honest - I could tell no difference with my RV275's. Thats why I switched to +75. I did notice them. I picked up around 1-2 mpg on the RV275's. I picked up around the same with the +75's. I have lost 0.5mpg-1mpg around city - which I attribute to stomping on it more with the extra 75 ponies when I am not cruising. So ...... for mileage RV275's probably best. For balance of power and mileage = +75 CPP. :2cents:
Link to comment
Share on other sites
Blueox01

Blueox01

Posted
  • Author
Posted

I'll be honest - I could tell no difference with my RV275's. Thats why I switched to +75. I did notice them. I picked up around 1-2 mpg on the RV275's. I picked up around the same with the +75's. I have lost 0.5mpg-1mpg around city - which I attribute to stomping on it more with the extra 75 ponies when I am not cruising. So ...... for mileage RV275's probably best. For balance of power and mileage = +75 CPP. :2cents:

I think the big reason i felt such a difference was the fact that i had 780k on my injectors,any NEW injectors would have made a big increase in power.:cool:
Link to comment
Share on other sites
Blueox01

Blueox01

Posted
  • Author
Posted

Does'nt have any LEDS just a jumper to switch.But i did finally get around to testing the data connector for Voltage and had none,futher inspection found broken wire.Sure going to be a pain to get a short piece of wire soldiered on in that location:mad:,finding a pin should be no problem.

Bought me a new pin and weather proof plug,soldiered new wire in shrink wrapped up,Edge working now.:hyper:
Link to comment
Share on other sites
 Share
Go to topic listing
×
×
  • Create New...