2nd Generation Dodge 24 Valve Powertrain

I believe my drag link is wore out? The auto parts store website calls them the tie rod ends? There is some play in my steering wheel, but it doesn't wander around on the road. What I'm trying to figure out is if this is causing the vibration that I am having. It only happens between 30mph to 45mph. I don't really feel it in the steering wheel, just mainly in the floor board. The vibration is there weather I am braking, cruising, or accelerating. But like I said Its only between 30 and 45mph. Between 0-29mph and 46-above, its very smooth. Any ideas? I plan on going with moog parts. If I uploaded it right, I added a video of the drag link movement. tie…

Hey guys, finally got enough funds to install a Boost, Pyro, and the much needed Fuel Pressure Guages! I looked in to having them installed but it's going to run me around $300.00! So I thought I'd save my self some $ and try to find a step by step installion for them. Does anybody know where I can get my instructions preferably with pics? Thanks to all who chime in!!!!

My truck has been sitting for several weeks in the shop not being used. It has never leaked anywhere except the crankcase vent then only a couple of drops after parking. I have the 47 tranny, 4 wheel drive with 102,000 miles. I dropped the tranny pan and adjusted the bands about 5K ago and filled with fresh fluid. Pan was very clean. Now after sitting probably 7 weeks I start seeing a leak where the transfer case and tranny meet. It didn't start leaking until this week. Any ideas?

Hey all! This post my fall into the category of post whoring but I'd like to risk that in the hopes that it may help somebody else out when trying to decide what to do with their 47/48RE when it needs a bit of help. I want to be very clear here, the transmission in my truck had just a hair over 100k on it when I was contemplating this. I also know how it was driven since I know the PO of the truck. He didn't flog on it and took it in for service at the dealer every 25k just like clockwork. I felt very confident that it was in reasonably sound shape. I was experiencing TC clutch lockup slippage on the stock TC. It started when towing my 32 foot travel trailer b…

So over the past few days i have been dealing with an issue with my truck. Sometimes it starts when i put the key in and turn it sometimes it doesn't... this morning fine, this afternoon fine tonight at the fuel station nothing. the only why to get it to start is jumper across the terminal at the starter with the key on.... any thoughts would be greatly appreciated.

I am seeing a constant 21-23 pounds, is that too much?

my 2001 2500 24 valve auto needs help, when cruising at 90 km and wanting to pass another vehicle, step on the accelerator, truck kicks down, speeds up to 100 km or so then falls on its face rpms go to governor but truck wont increase speed any more, have to pull back in behind, any suggestions

he Lowdown on the New Low-Viscosity Oils TMC session examines what's going in to the new API engine oil standard and what engine makers are doing to prepare. March 2014, TruckingInfo.com - WebXclusive by Deborah Lockridge, Editor in Chief - Also by this author SHARING TOOLS |PrintSubscribe Share on emailShare on facebookShare on twitterShare on linkedinMore Sharing Services6 Kinematic viscosity is what you might envision when thinking of viscosity – gravitational flow. But the new oils will meet viscosity standards measured at high temperatures/high shear conditions. To meet the expected greenhouse gas/fuel efficiency standards that…

What's the best filter for a 47re? I guess the search function and me don't get along...

The other day I broke the handle off on my ATF dipstick and had to cover the fill tube with aluminum foil till a new stick comes in on Tuesday. Since covering the tube with a plastic bag then foil and zip tying so it's almost air tight and isn't going to fall off the transmission is shuttle shifting between 3rd and 3rd lock (OD off, around town driving under 50mph). Does the fill tube vent transmission pressure gas? And could this cause my shuttle shift? Or should I catch up on the lock/unlock topic?

Alrighty gang, I finally got my new switch installed last weekend. I figured I would go through some of the basics on how I did my install just so others can have an idea on how to do theirs. When you get your switch in the mail, it should have the following things included: -The actual switch with wiring and connectors -A small piece of 3/8's heavy walled plastic tubing -Three 1" screws If something is missing, DAP will take care of your needs. If not, I am sure Ed could lend a helping hand wherever needed. First thing I did was remove the dash bezel. It just has pop clips all over the place that hold it to the front of the dash and around the cluster, radio,…

Howdy! I'm having some brake drag coming from the calipers in my truck. Here's a little background on how I got here: Worn out ball joints started me down the rabbit hole of a front end rebuild. I've got new ball joints, hub bearings, rotors, brake pads, track bar and steering box brace. The good news is it drives about like it should tho new TREs are in the near-ish future. That should finish things up and make it all good under there. I changed the pads and rotors because they were old and thin and the truck had started pulling to the left under moderate braking. Hard braking was straight as an arrow. Go figure... After I installed all this new hardware and …

Is it just me or does it make the truck a bit more peppy on the low end. I had to go to a service seminar 4 hours away from home. At 1 intersetion in particular you have to make a sharp turn to the left. I attempted this manuver...at a slow speed ,darn near did a 360 right there. Granted the roads were wet and I have studded winter tires but it was quite warm. WOW it works nice. I drove Like Michael told me for the most part on cruise at the speed limit. I had the Edge set on 5x3. Hand calculated is 20.76 mpg. I am pretty happy with it. A set of RV 275 or so injectors and it should be sweet. I wonder what these trucks would be like with an unlimited computer co…

All right, I ordered a new set of RV275 injectors and feed tube o-rings from DAP. They will be here tomorrow. I got all my old injectors pulled today. It was actually fairly easy, I had figured 5 and 6 were going to be a pain but they weren't. I can return my old injectors for a $100 refund but I was thinking about keeping them for a spare set. I decided to go ahead and take one apart tonight, and noticed there were two washers inside the injector above the spring? I've never taken one apart before, but isn't there only supposed to be one washer? Do you think the second washer has something to do with pop pressure? Injectors wore out? Also, just to make sure I hav…

I frequent this site to see if there is something I just gotta have... and this 1998 2500 caught my eye. Current bid is 4000.. No. I'm not interested, but I was searching 'flatbeds' and this caught my eye! seems a little odd placement of fuel pressure gauge?? supposed to have a fass, ats 3 piece exhaust, ats transmission, and firestone air bags.. then I seen this: My guess is this onboard air compressor is for air bags, and that gauge on the corner of the cab is for the air supply?

Somewhere I looked over a write up that I think Mike wrote or fixed up about what the settings on the Edge did. Explained about each setting and its affect on fuel and timing. Of course I can't find it now and did not copy it. Could someone point it out to me . Regards Chris

Hello, Been A while since being on. Busy working! I Bumped my truck over and didn't hear my fuel pump run. Shouldn't it run every time you key the starter? The fuse was good on the air dog. I tested and had voltage on both sides the truck off. it when trouble shooting my truck that didn;t want to start at work today. Think I have a starter issue as well. Thanks for any info. Also been having very cold temps and snow. JOHN

I have two axles that I am considering changing the internals from one to another 1. I have a Dana 70 2u (factory disc) that I picked up the other day, and it is trashed as far the internals go. 2. My good Dana 70 2u (drum) has about 300k on the clock, and its in good shape from the operational standpoint. Is the disc worth building, and having under the truck? It will take quite a bit of steaming all the metal out of the axle to get it to where it will be safe to run the axle long-term. Another thing I have considered is removing the flanges via cutting them off and putting the disc flange on the drum axle( minus the drum flange). I look forward to any…

Ok I can't seem to figure out what the noise my engine makes. I just installed my edge comp box yesterday (Not wire tapped) to make sure everything was going to work properly when I do decide to tap the pump. Now when the engine is down in the lower rpms and i stab the throttle I get a slight loss of power, and a terrible "grunting" sound. To me it sounds like the timing is WAY off from what is should be, But as soon as I build a couple pounds of boost the horrible noise goes away and the power comes on instantly. I have no codes, smarty is set to stock, FP is 15wot 19idling. IP is 2 1/2 months old. I thought I had read somewhere that if the MAP sensor voltage is way low…

Any one had these 4 trouble codes at the same time? Truck will not start. I have not had time to look the truck over yet. so i don't know battery voltage yet or if i have any lose or broken wires, plan on looking it over this afternoon when it warms up a little. Thanks for the help p0382 p0380 p0215 p1689