2nd Generation Dodge 24 Valve Powertrain

I still get fuel pressure and it will start, just no WTS light at all anymore. ecm?

I was having problems about a month ago. Truck cranked but wouldn't start. Check engine light on, codes present were 1688, 1689, 252, 254. Injection pump was replaced. Same problem, same codes. Took to local Chrysler dealer they cleared codes and said nothing was wrong. Drove to get fuel, truck was idling and just died and cranked but wouldn't start. When it finally started it wouldn't go above 1500 rpm's drove home on shoulder 8 mph. Sometimes when key is in the on position waiting for start light speedo needle with jump up and down and CEL will flash on and off. Help please!

Going to do brakes and power steering fluid... Haven't done before, couple questions:1) what size tubing for caliper coupling?2) when doing rear passenger wheel, just keep pumping until it turns clear then move to next wheel...?3) what happens if air gets in line - how will you know? Will brakes get spongy and I'll have to rebleed... One wheel or all wheels? 4) power steering - just use a turkey baster? Thanks!

Got a goulds kit and going to tackle the pump seal issue. Got the video and i know how to do it. The problem is none of the videos or anything tell me the best way to actually remove the pump and PS unit from the truck. I know to do it as one unit, but you guys that have done it, which way did you go? Out the bottom or top?

Hey gang can we help this new family member out with not only his truck but how to use the forum too. First thing I typically ask for is error codes (using a OBDII reader) and fuel pressure (idle to WOT at highway speeds).

Moparman says I need a big line kit with my raptor 100 on my 2001 stock Dodge. How big? Big lines all the way to the injection pump? I know about the high flow banjo bolts but are there big line banjo fittings? I am thinking about the XDP sump instead of a larger draw straw. Any thoughts on that? Can I still use the stock fuel filter?

Hey guys,I took my 02 cummins in to the dealer today to get the high idle activated! and the diesel mechanic told me that he is unable to activate the high idle on my truck because it is 6 speed standard! he says that its not in the programming! true or not? any body know?Thanks Reg02

Well, joined the forum back in Nov... had been working on plotting out our tune up/ preventative & maintenance plans and before we got anywhere within driving the truck an additional 500 miles at most we have MAJOR ISSUES... needless to say we have have the truck parked in the driveway since we put new tires on it at the end of November, we have had to start it a few times to move it for snow removal and driveway access issues... So here goes the saga of problems... this fall we noticed that we were having issues with the truck shifting around 45 mph... after much reading on this forum, I do believe that it probably is the same torque lock/ converter issue that m…

I'm replacing my head gasket and took the head to the machine shop. They just called and said its cracked . Is this common? Where is a good place to get one? Any input would be great.

Well, this morning after changing my fuel filters i was in the process of jumping power from the battery to the plug for my raptor to bleed the air out of the system when i had a brain fart and grabbed the plug for my deleted fuel heater instead. There was a spark and immediately put the CEL on. So i grabbed my smarty and checked the codes...p0222 idle validation...p0113 IAT sensor voltage high p0118 ECT sensor voltage highp0238 MAP sensor highp01693 companion code I figured i just blew those sensors so i went and picked up a new ect,map,and iat sensor and installed them, cleared the codes with my smarty and lo and behold those codes pop back up again. So in desperatio…

I am new to the Diesel world i have a 99 2500 4x4. The problem that i am having is when i start it up and barely press on the throtle or press the throttle to the floor it will only go to 1500 RPM. I can take off the negative battery cables for about 30 min and reset everthing and it may a run couple of months and then it will happen again. Can any one give me some insight on what to do to fix this problem?

Hey guys. I'm at my uncles this weekend and he says he had a programmer that changes tire sizes. I have been wanting to do that for a bit so I said sure. I didn't even think it would try to tune my truck also. I have my comp box in the truck as well. I set the tire size and went for a drive. It felt like the the timing was all over the place!!!! I turned the comp off and it seemed to smoothen out but I have a serious power loss now. I tried to get back in with the other programmer to erase all its settings and now it won't recognize the truck. It says that it's not the original vehicle. This programmer is a smart chips "micro max" tuner. Obd II plug in. I have to drive 20…

i bought a 00 cummins with alot of k. engine is tired found an 02 with 120kms for dirt cheap. i heard the interchange is 02 only? what is different?

I was wondering if removing it the silencer ring actually gave you more boost or cooler egt? I know it gives you a little more whistle didn't know if there was any other benefit to it. Thanks

Hi noobie here on this site!Just wondering! I'm having hard time finding any info if it's ok to run the Rotella 0-40 syn diesel oil?? I'm in northern Ontario and we see temps as low as -50 Celsius!!! ya it gets really cold! I heard of lots of guys running the oil up here and getting 400,000 + km on there rigs but sill just looking for some more input!Thanks

Hey im doing a clutch install in my 02 six speed. Got the trans down and out and im looking for my pilot bearing but there is none. Nothing. Stock original clutch. Did it bust apart and fall out? Also, there is alot of what looks like grease and oil in the bell housing, im guessing from the throw out bearing, but there seems to be alot of it. The bearing spins very free and has hardly any play in it. Dd the grease come from there? The input shaft has very little play as well. Where else could the **** come from?

I just checked out the XDP fuel tank sump and like the idea of it. I can install it without pulling the fuel tank. Are any of you guys running one? They are a bit pricy, but worth it I think. If I install one I'll go with a half inch stainless line to the front and mount my Air Dog FRRP back near the tank. That should solve any fuel issues.

Greetings-From Steffen at DTT ...I purchased the Assassin Mechanical Fuel Pump for my '98 24 Valve-I also purchased the Vulcan Double (Filter and H20 Separator)To install along with it. My idea of how to install the Pump etcis as vague as the instructions included with the pump. Which consists of a simple line diagram with little or no descriptions of where different fittings, filters, hoses go...there are not even instructions as to where to put the pump...where the individualbolst may go. Yes-given lengths of time and trial and error I could most likely figure it out, but I have had my truck off the road (A FUll MOTH) waiting for this pump. I already replaced my Inj…

Putting rv 275 in right now. Where is that thread that tells you how. Just need some torque specks for the injector holders. Little 5/16 nuts. Thanks

:banghead:Yeah gang... I destroyed my turbo with a wire hose clamp. During my oil change and boost leak fixing I laid my BHAF on the workbench and inadvertently knocked a wire hose clamp in the BHAF from the peg board above. Installed the filter and took a ride. Boost kept getting lower and EGT rising whistle changed big time. Hua?! Went home to find the first pic and the 2 ears of the clamp in the BHAF. The rest of the ring I'm hoping is in the intercooler. :pray:Engine still runs fine... So I need a turbo... First and foremost.I know that S#!7 happens but man this make me sick...