2nd Generation Dodge 24 Valve Powertrain

got a pretty good leak going on, apperantly at the return tee at the back of the block. i have gone under the truck while the engine is idling but cannot see it leaking. it is however soaking wet. the fuel is coming down and hitting the front drive shaft and is being slung all over the place. when i park i leave a small puddle of diesel and can smell it pretty good. since i cannot see it leaking i am assuming the engine needs to be under load for it to leak.anyway its going to be a pita to work on. so anything yall know to make it easier would be appreciated. i am going to buy a new tee and replace it while i am back there. is there anything else that ususally fails in th…

Newbie here, play nice. My son's 2001 24V 6Sp manual has started an interesting/frustrating new habit. Seems as if once the beastie gets up to temperature and your changing throttle positions I'm getting an uncommanded shutdown. I verified this phenomenon this afternoon by shoving a thumbtack through my Red/Lt. Green 12V+ wire going to my VP44 and hooking up a VOM to it. Sitting in the driveway I let it idle and gave it some light accelerator action until Barney the Wonder Mule warmed up. I opened the throttle to about 2000 rpm once it got close to 190 degrees and ran the accelerator pedal above and below 2000 RPM about 200 rpm either side of the 2K mark. Sure enough wit…

Man, I need a break... this morning, went out to get ready for work.. start truck for warm up. Leave about 10 min later. About 4 miles from house, look down at gauges and no oil pressure, turn around, go back to house. Check oil, ok, it was a little low (Qt & 1/2) but not enough to show no pressure. It didn't knock or run any different than normal. So I check the gauges out ( key off, push and hold trip odom. button, turn key to on) Everything checks out ok. So I figure its the oil pres. sending switch. Call Autozone... $197 bucks. No way i'm paying that, can get a aftermarket for $100. So, I drove it today, no problems: water temp ok, no engine nock, the c…

my head gasket went again. found a big puddle of oil under the truck and its coming out right in front between the head and the block. i did the head gasket 9 months ago and put ARP studs in and was really hoping it wouldnt go. didnt think it would with only 45psi boost. any ideas on why?

So picked up the engine for my truck today. Im not really sure what I ended up with. I cant find a 53 anywhere so I hope that is a good sign. The block in my truck has a big 53 on the drivers side lower front of the block. This block has a series of numbers. The tag says it was built 3/3/98 and is rated at 235hp. My tag says 215hp. This engine must have had a manual behind it? My plan is to swap most of the parts from my engine to this engine so I hope I dont have any problems. --- Update to the previous post... Oops. I put this in the wrong section. This is meant for the 24valve section. Sorry.

http://www.rocksolidramtrucksteering.com/ I just found your information searching sites for my steering issues today and i was about to spend lots of money to try to fix my issues. I was reading every ones replies and crawled under my truck and had my wife turn the steering wheel with and without engine running and didn't see any play that would cause the steering to wonder as bad as it does, so i grabbed the column and my bearing at firewall is completely gone, so i guess i will be ordering one shortly

I am about to rebuild my front end steering in my 01 dodge ram 2500 quad cab 5.9l 6cyl. and they asked if its a 3500 lb or 4500 lb front axle both show dana 60 which i have, so how do you tell which one is which?

I don't know exactly what did the trick. Went for a test run and pressure is up over 14 on a stock pump. It stays there on wot.All I did was take the top off the stock pump and removed the screen on the inlet side. I know I can junk the screen cause I have a prefilter.Just wanted to let you guys know how it made a difference. I think I can attribute it to that.

heres my problem. my rear drums on my 01 are very touchy dont think my fronts ever even grab. if im goin down a dirt road in 1st gear and tap the brakes they will lock up in the rear. my parking brake doesnt work either. hope i can get it fixed before the ice comes. any ideas?

Fellas, I know this most likely has been talked about and maybe way way back I even started a conversation on it, but my surging is back and i'm looking for thoughts. All summer my truck seemed to work fine with no surging, now that the weather is getting colder , i'm starting to feel it alot. Today it's about 4-5 degrees out and when driving along trying to hold a consistant speed I feel it surging up and down. If I use cruise control it maintains speed with no surging. I'm running 16-19 psi for fuel pressure always , no codes showing in the odometer. I remember last time I had issues I did a reset on the apps, even adjusted the voltage on it, took the IAT sensor out and…

Anyone have any input on the exhaust manifold I should get? I'm undecided between the BD and ATS. While the BD has two ports driled and tapped and the ATS has one. The ATS also comes with a high temp black coating and won't look like crap after a few seasons. As far as quality between the two I have no idea. Currently the best price I have found shipped to my door is $425.00 total.

Ok, So I bought a 2000 dodge 2500 4x4 auto, quadcab. When I bought it is seemed to run and shift fine. I got a pretty good deal on it and was a little worried something might be wrong. Well of course I didn't know about key trick to check for codes until I started working on it at home. When I bought it there was only 1 battery, so I bought two new batteries and installed. I also bought a raptor 100 and installed along w/ fuel filter. I did both of these at the same time. Since then I am getting 3 codes. p1693, p0216, and P0123. I know the first two point to mechanical ip failure, but it still cranks and runs good. The main problem I have now is the p0123 code…

will 2011 dually rims fit 2001 dually

I bought my truck as a basket case you could say. The shop that found the crack in the block just left the engine torn apart. Im picking up another engine with a bad vp saturday for my truck. I will be swapping my vp to this engine. I was told the vp that my truck came with was "newer". Problem is the shop didnt cover the ports for the injector lines. Is there a safe way to clean/flush the pump?

When it gets cold my fuel tank is pressurizing. u can here it hiss out of the rollover valve and when u take the cap off u get a wosh of air. it only does it when its cold whats going on?

my fan hub bearing is making noise and im gonna change it but having trouble finding a bearing. got the part number from cumminsp/n 3910739number off bearing BD35-12DU8Athey want 250 bucks for it. which is ridiculous. cant find it anywhere else though. any ideas? thanks

I want to publicly thank you Mike for this forum and all the work you have put into it. I have needed to change the injectors in my truck for about a year and a half but I could not ever get enough ahead to make that happen at a shop (1200$). After ready this forum and studying as much as possible all the procedures I said screw it I am gonna do it myself!!!! Took me about 5 hours but I was quite happy that I managed to do it myself and it would not have been possible without this forum and all the members..THANK YOU!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!:):)

My turbo is leaking air underneath at the connection after the elbow!!!! Any one know what the part # or if I can get this gasket at one of the national parts stores. Thanks in advance...

im building a high idle fooler for my 02, and i hooked up to the dodge drb3 and truck has all the recent updates. i put the 3.3k ohm resistor in the ect sensor and the 39k ohm resistor in the iat sensor. ect reads 128 F and iat reads 26 F. still no high idle. any ideas?

Hey fellas, I know it's been a while since I have posted! Been extremely busy lately at work! But any ways my brother has been driving the "beast" alot more lately than I have, since I bought the 06. Well he tells me it has been kinda of spuddering a couple of times but it clears up, well today he was driving it hauling a trailer and 30 hp new holland tractor. He says he was cruising about 45 mph and all of the sudden it spudders, and starts knocking a little and immidately shut it down! He also said that it's bellowing coal black smoke! Talked to MoparMan, and we both feel I have an injector problem. Going to tow it in tonight and start tearing down to see!