2nd Generation Dodge Reliability / Performance

Having a little problem. I searched and didn't find an answer. I have internittent hard starts. Hard to isolate a common denominator except when parked at an angle. It always cranks extra before firing then. Other times it just does it, whether it's been sitting for awhile or just a few minutes. This is the problem that doesn't bother me too much. The other problem is there is consistantly fuel in my oil. These problems just began when I installed my new injectors. This was my first install and I took my time and follwed Mike's instructions. No big deal or problems on the install. Since then I have noticed that I have fuel in my oil. I changed my connector tube o-rings an…

After months of thread reading and lots of research I have come up with some economical upgrades I think will work for my application without breaking my bank. Now I need some feed back to assure myself I'm thinking right.What I have besides limited funds is an 01.5 daily driver with 225,000 miles, pulling 8-15,000lbs about 50% of the time. Other wise I'm running 90 to nothing having a blast. Here is what I want to do.upgrade to dodgzilla turbo, rv275 and bd boost fooler. Keep my torque dog and add some gauges to keep track of everything. Tranny has been done rite locally so I'm confident about that.Am I on the right track??? White 01.5, auto, quad cab, sport, 4x4, long b…

First a 17mpg tank while towing (total flatland slow speed fluke, but I'll take what I can get), the only issues were really simple (exhaust brake linkage lost a C clip; broken fuel tank strap with no damage done at all), and now.....I was prepared to tear my dash out to get at the top of the heater box to deal with a stuck blend door. I pulled the heater controls first and found a kinked control cable. Detached it, straightened it out, and all seems well. Door moves, not sticky, not jammed, nothing. Hope it stays that way!SCORE! :thumb1:Maybe it's getting ready to treat me better. Maybe it'll treat me well enough that it will get some body work out of me

Just wanted to see if everybody is using 65 psi front and 50 psi rear when empty on a 2000 dually. What is the recommended tire pressure when hauling 15k lbs?

Is there a proper way to drain the water seperator on a fass 150? Whenever I open the valve on the bottom of the canister it seems like fuel just keeps coming out.

Ok I feel like an idiot I have almost every gauge known to man in my truck but I wanted to put some on the a pillar so I thought just go buy and a pillar pod right. I did and it was suposed to be cut to fit and basicly glued to the old one I sent it back thinking I could find a better mount with no avail does any one know of a pod that just replaces the stock one and clips in where the stock one did is this possible or am I asking to much

I going to install some rv 275 injectors in the near future. Also a j- hook, but what kind of boost fooler ( diablo power puck ) not wanting to spend $1000.00 on edge. I may trade the truck in 2-3 years for newer.

"In this case we found a way to get better fuel mileage and a little more power on some trucks. This pump has ALL the upgrades and improvements that our exact replacement units have." "What we did to achieve this goal was to mix and match parts from other VP44 pumps to advance the timing mechanically and optimize fueling rates for better mileage." "If you are presently or plan on advancing the timing with an electronic plug in device or programmer don’t buy this pump as we are only doing mechanically what those products do electronically. " "The Special X pump is made from all Bosch made parts. It does not have any aftermarket or modified parts in it, so this allows us to…

I thought I would pass on some info for everyone! I had been talking to Mike "mopar1973man" about adding the scangauge II to my truck, but I am already using the OBDII port to run my Edge Attitude with Juice CTS! Mike an I messaged eachother back and forth, while Mike came up with a feasible idea of hard wiring another OBDII port into the truck, but with unknown an unforseeable issues! I called Scangauge and talked to a lady that was very helpful, explained to her that I needed the OBDII port to run my edge, but I also wanted to run their ScanGaugeII, after a few minutes on hold, she came back with the info on a site that has a "Y" adapter giving you the option of running…

Got my raptor 150 and quadzilla chip and have a few questions before install first one I have a short bed and to install the raptor it looks to me I have to mount it on the outside of the frame is there any problems doing this and the other question is looking at the fuel lines on the tank witch one is the return line and witch one is the feed now on to the chip I understand everything but what wire you tap on the vp 44 thanks in advance

I just installed my airdog 165 fri night and sat I was having problems with it cranking and now it surges going down the road! This morning it took forever to start! When it did crank, drove it to the office and had to keep the idle up and the check engine light came on with the following codes P1692, P1693, an (2) P0122! Any ideas on what to do? I did the fuel module install! Please help!!! Jason:banghead::banghead::banghead: --- Update to the previous post... I finally got the pressure gauge to hook up an I am running 15 psi! Just as soon as I get it started, it is still loping! I believe I am sucking air some where but I don't know! I took the fuel supply line of…

Found these injectors on Ebay from from a shop called Pensacola Diesel, http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&item=200587208258&viewitem=&sspagename=STRK%3AMEWAX%3AIT#ht_550wt_1167. You know the old saying, you get what you pay for, so this price scares me a little. To good to be true for that price? Anyone have experience with that shops parts?

Just got my BHAF installed with the stock tube and a black outerwear. Holy hell, my turbo is screaming. Atleast my truck sounds fast now, hahaha. Couldn't use the filter minder due to a crack at the bottom. Guess I'll just leave it out for now and maybe pick a new one up later. So far very happy with it.Question though, the bolts sticking up through the fender for the stock air box, did most just leave those in place? I left them just in case I ever switch back and didnt really even look to see if they came out.

Has anybody had issues adjusting the pressure on the airdog2/165, the instructions say 2 turns clockwise equals 15-16 psi, but my gauge says 26 psi. Trying to reduce pressure but if i go all the way counterclockwise on the airdog i only get 21 psi. Is the air dog wrong or the gauge?

today, i was going to install my thermocouple at the exhaust manifold, and drilled a hole and found out that theres a wall inside the manifold right under the center where it connects to the turbo. i tapped it but im not sure if i will get an accurate reading. Has any body had this problem? looks like the place i picked to drill the hole has a wall inside the manifold and the hole passed just next to the wall.

My truck is a 1998 dodge 2500 short bed quad cab with a 12v and a 5 speed. Mods: Auto meter gauges 66/74/14 "Better Bullet" built by Chris @ E.D Weston 5x.014's 191dvs 4k gsk 5" dual exhaust #100 plate ff with afc cranked 20* timing South bend Iron Giant 4200lb dd w/ big input Fire ringed head w/60lb springs and valve work ARP head studs Bhaf Detroit true-trac Mag tech rear diff cover Adjustable valet switch High idle mod Ram air hood Lame flame paint that I want to change someday. Galaxy cb radio, road king mic, "little wil" antenna Alpine deck, alpine mrp-500 mono amp, JL 10w3 Best Dyno 453hp 939tq ***EDIT: Added …

Are these hard to install I want to gain fuel mileage and power the raptor fuel pump I want is the 100 gph how much horse power are these good for I would do the 150 but don't want to mess with the draw straw the edge I want is the juice with attitude to monitor egt fuel pressure and tranny temp will this work for me I eventually want to do ddp injectors probably around 100 125 when I bought the truck I was told it had 75 HP injectors and it does have 4 in down tube with 5 in straight exhaust but I really need to do a fuel pump soon side note had tranny checked it had been rebuilt some time and has a shift kit nothing else is known thanks in advance sorry about the long p…

Hey guys.Got tired wondering which was better.HX35, HE351cw or Super HX40.So ---- bought a HX35 (Im an auto running a HY35) and sold it without putting it on. But have now bought both a Super HX40 and a he351cw. Going to feel the differences for myself and post results here - both spool and EGT and boost/feel pressures.Took my hy35 off today. Bolted on my HX40 with new DP to find I am 4.5" short ..... due to elbow ..... so going to have to get the DP extended during week and put back on. Will update when I do.Then it will be off in 2 weeks maybe and put on the he351cw - will update on that too.For a funny side bit- I was yanking and yanking on the 4th bolt of the t3 fla…

When I first hooked up my mystery switch it worked great. Now it locks the convertor for maybe half a minute then it unlocks and I have to turn the truck off before it will work normally again. Gives me p0723 code which I had before too when it worked normally. p.s. I took the switch and wiring out when the truck went to the tranny shop for the rebuild cuz I didn't want them down my throat for using it. This problem occured after I got the truck back and rewired it.

I want to install 36" tires what should I look for a lift kit or level kit & how high should I go this is on my 2500 series cummins