Mopar1973Man

LOL... Working with the wrong ladies. @Wet Vette loves my truck it looks stock and for her hips and back much easier to get into. (We are both in our 50's). The power part she loves when it flat pulls like today passed 9 cars all in the same pull. Lead car doing 40 to 45 MPH and speed limit is 65 MPH. Kicked it to 75 MPH and walked the entire pile and took the lead never seen them again. That is a 2 inch leveling kit. The easy solution is to pull those spaces out. Return to stock rake. Then the rear spacer is stock for 4WD I've got the same one on my truck. To do it right you need to change the control arms to get the geometry correct this will allow you to correct the caster angle. and the track bar should be replaced with adjustable bar. This will allow to set the thrust angle to ZERO again which 2 inch leveling kit will pull the axle to the driver side too much. You can see my rear block on the passenger side which is the same block your running.

I'm off road all the time here locally. Going out in the forest for firewood. Etc. Never had any issues with my current set up. Like I've been doing for 20 years on stock tires and suspension 415k miles later... No road for long ways...

Should of used the moose mirrored truck...

Weird... I'm now in the 2 to 3 wait period now.

Well I learned something yesterday... Never go shopping in the economy car. We went to WalMart, Costco, etc. in Lewiston, Id and Clarkston, WA. Needless to say it was so much stuff we packed in that little car it struggled to pull the load and drop the MPG down into the 30's. Surprising that you start with a little bit and keep going to pick up everything that you have on the list of good deal while you can. Then start loading the car and finding out the car is filling up rapidly. Now you loading the back seat because the trunk is full. Make sure you use the proper vehicle for the task at hand... @Wet Vette little car (2018 Hyundai Elantra) was really working hard to climb two grade and keep up at the set cruise speed at 65 MPH. A few times I had to manual shift to get it to build power again and not let the engine lug down. No temp issues per say but working hard on that little power plant. Nothing bad to report but just something to consider...

Just signed up for my badge...

Dynamic built 46RE into a 47RE on my 1996 Dodge Ram 1500. As for my suggestion is double check the output speed sensor on the tailshaft. Mine was shifting at all weird times sometimes hold a gear excessively or down shift early.

Maybe a bad multifunction switch

Super sweet looking truck! I also like the logo too...

Power wash the engine off and use a good degreaser. Take the truck for short drive just a few miles. Then search the engine for a new wet oil spot or oil weeping. Common leak places are... Vacuum pump seals Tappet cover (cam cover). Front crank seal Gear case cover. Unscrew your oil cap while idling if the cap moves you've got excessive blow by. Rare to see on our trucks. Really common on the "Common Rail" engines.

The right is the new style NAPA which I'm using currently. The one on the left is the previous model napa which I've used in the past. Here is the junk Cummins T-stat... Be aware that Cummins DOES NOT manufacture any thermostats. This design started by Reobertshaw which no longer produces thermostats and then handed this off to Mr. Gasket. So you Cummins thermostats is not Cummins Design at all. The original design was produced by MotorRad back in 1998.5 to 2002 and you can no longer by that thermostat. Another member with Cummins thermostat that seperated... Robertshaw 330 - Called and verified no long manufacturing... https://www.flowkoolerwaterpumps.com/products/robertshaw-330-160-degree-thermostat Then Mr. Gasket. Which is now products by Holley... Current manufacture. https://www.holley.com/products/cooling/thermostats/parts/4365

Lift and leveling kits are typically the cause of front end steering issues. This all stems from the fact you alter the geometry of the axle. I left my truck stock and every thing last much longer. Ball joints 200k and counting, tie rod ends 350k miles on OEM, track bars 150k miles, steering box 350k miles. Etc. If you want to short the life your front end just add a leveling kit and bigger wheels. Then you can cut this in Half or even less. I'm running 245/75 R16 tires (30.5 Inch), no lift, no leveling kits... Truck in my sig.

Been running only NAPA thermostats no issues. Typically doing 75k miles and do coolant flush and fresh thermostat. Matter of fact I found my last Cummins thermostat I changed for a customer being it fell apart. Ill post a photo when I get home.

Another 1 million mile truck coming... 900k is very impressive. Keep going. 415k miles... I'm another lap back and forth to the moon behind.

Like myself I've had a long conversation with Michael Fabian (Facebook member) the conversation gone on for over 3 hours discussing about VP44 and fuel system design and how to improve. We both agree that fuel pressure is optimal for 99% of people here for 14 to 20 PSI. There is nothing to gain above this. There is lots to lose for fuel pressure below 14 PSI. I know several have mention how they ran 5 to 10 PSI without any problems but the life span typically end up being shorten from low pressure. Being I've actually check that when the pressure is below 14 PSI the overflow starts to close and then its completely closed at 10 PSI. The extra cooling and lubing will end at 10 PSI. The 10 to 14 PSI may vary from valve to valve a bit but the cooling and lubing does slow way down in the range and stops for the most part at 10 PSI.

I never even look at the fuel pressure gauge just watch for the light if pressure is low.

Already got over 100k miles on my current pump. I'll most likely make 250k miles again.

My old warning light I've home crafted for my DiPricol Fuel Pressure gauge which had no warning light. The red warning lamp will catch your eye just enough you don't have to look at the gauge but the level the light pops on at. Bottom I know is EGT's, middle is fuel pressure, the boost on top.

For me only drop about 2 PSI from Idle to WOT. Set for about 17-18 PSI and stops at about 14 to 15 PSI. Very very stable. 250k miles on my first AD 150 pump after 13 years. Lots of idle time!

You can drive it home but longer you drive it the way it is the more damage is being done to the VP44. The VP44 injection pump needs to have return fuel flow at 14 PSI to 20 PSI so there is cooling fuel present and excess fuel to lube the pump. Being that your below 14 PSI the return valve is CLOSED there is no cooling and no extra lubing for the pump.

No holes, no cuts, no duct tape. I just lifted right up between the exhaust pipe and turbo and lifted the cab right near the outer heater hose.

Here is what I'm using is a Vulcan Performance fuel pressure tester. 0 to 30 PSI gauge. This is much more accurate than a 0 to 100 PSI gauge. This is 1/2 pound tick marks in the red. I even got all the fittings for all types of fuel systems. 

Nope, all the way towards the cab and all the way up. Not quite. Ive gotta lean over a bit to see the bed corner.

Lift pump is dead time to replace. AirDog, Fass, mechanical belt driven, etc

ZERO. I placed the stud in the hole. Then using a 2x6 lifting from the floor up to the cowl using a floor jack I slowly jacked the cab up nearly an 1/2 inch and the stud fell in the hole by itself. The rubber of the cab mount compressed over the years and just need to lift the cab slightly just about 1/2 inch and plunk in the stud. NO HOLES DRILLED or CUT in the cowl.