2nd Generation Dodge 24 Valve Powertrain

Started truck today abs and air bag lights are on also ac blower motor would not come on. Started down road blower motor came on and lights went out. Started truck after work same thing no codes anybody had this problem? Thanks ed

I have had it on my truck now for about 3.5 months now it was at 15psi idle and 22 wot now my idle psi has dropped to 12 but wot is still the same.Will a dirty filter cause this I have not checked it yet but will tomorrow.I changed the filter when I installed the pump I would say that I have about 4000 miles on it.What else would cause this. THANKS

i was just wandering when you guys rebuild your engines what brand of kits do you use and can any machine shop do the work or is this something you have to make sure they know what their doing? how many of you guys do your own rebuilding, is it pretty easy or a thing a pro should do. i have rebuilt gas engines but never a diesel .

P0460 P1595 P1693 fuel lever didn't work in two years cruise stopped working over 6 + month ago fuel pressure is 15 at idle and 12-14 at cruise and maybe 12 at WOT Very hard start daily changed both fuel filters one on engine and the small one pre my lift pump nothing changed I ran out of fuel 3-4 weeks ago and had to open up the injectors to get the air out and truck was fine for a week or so after that then the hard starting problem started I reset the APPS a couple of times and does not help at all

Been driving about a year after the 0216 code came up. It never came up again till a few days ago so I increased fuel pressure to 21-22 from 18 and throwing 2 quarts of 2 cycle with every fill up to help the VP.I have a significant increase in miles hauling the same heavy camper on the same almost exact 3 day long road trip sometimes going 3 times a year.. It's showing a little over a 1 mile per gallon increase to 15.3 from just under 14.:think:I thought the vp should give bad miles when the timing piston starts to wear (0216 error code), but there's no white smoke and no hard starts. runs really good.

This will be a little difficult to describe. When I first get the truck rolling in the morning, I'm hearing a rubbing sound which sounds somewhat rotational, in that it is not constant. It seems to be coming left front. It started a few weeks ago after I changed my crankshaft position sensor, where the only thing I had done was remove the started and reinstall. I have not lifted front end up yet to check wheels, but this noise stops after a few hundred feet, and seems to be only when the truck is not warmed up. If you have any tips please let me know so I can start checking into some things. The starter is brand new rebuild as of yesterday (warrantied one went out yesterd…

Performace Diesel Parts + New Toyota Offering Sale Ends August 31st 2013 Diesel Auto Power is proud to announce that we stock Extreme Head Studs for Dodge, Ford 6.0L and Chevy. Extreme Studs are made from a fine grain, hi-strength - 240k tensile tool steel H13 specifically designed for heavy duty, hi-shock applications (DIESELS). Compare to other studs that sell near $1000. Prices Start at $610 Extreme Studs ------------------------------------------------------------ DODGE CUMMINS ------------------------------------------------------------ Diesel Auto Power offers a full line of replacement and performance injectors fo…

I would like to add the fuel filter as try keep debris away from raptor pump(raptor 100) but I has research and not see what is correct way for me to get a part kit to do on my 2002 dodge ram 3500 cummins as 2wd dually. Also I had noticed the my raptor 100 would not increase te pressure even I did changed the fuel filter at stock canister that did increased from 15psi to 21 but now it went back to 14psi after few weeks driving. I had not get chance to pop the line off at raptor 100 to see at screen to see if plugging up? I had put my cummins into my garage and stay inside for few weeks as had not get time to look at it. Also do I should just upgrade for two filters with…

Coming home from my trip to Texas last week and I see my isspro mechanical water temperature gauge setting about 215* but the gauge in my cluster and my ScangaugeII both reading 188-190. I check my gauges periodically when im driving my truck so I know it was not doing it very long. We stopped to run through the Chik-fil-a drive through and after about 10 minutes or so being back on the road I noticed it. I was running 80 so I backed off down to 70 and it came down a little, maybe 210 or so. I kept a hawks eye on it for the next 10-15 minutes and it just dropped to 195 or so like normal. I watched it the rest of the trip and since but it has not come out of the normal ran…

I have a P0122 TPS code on my 99 Cummins that I cannot get my scanner to clear. When I read the codes it was listed 4 times - twice for confirmed and twice for pending. I told it to clear all codes and I still have one confirmed and one pending remaining. I've tried several times but it won't clear. Any ideas would me helpful. - - - Updated - - - My reader is an ACTRON 9575.

2002 3500 dually 6 speed 200k. Bought this truck late spring, finally getting around to fixing things. Needs new rear rotors. Went to take the rear wheels off, passenger side came off fine. However the Drivers side inner wheel is stuck solid! Looking like some rust in there where the wheel mates against the hub. Dammit! :banghead: I tried everything, doused it with WD40, beat the tire (not the rim) with a hammer, won't budge. Kicked things up a notch and took the truck off jack stands & put the weight of the truck on the wheel & drove it back & forth in my concrete driveway. Nothing! Chirpped and spun the tires on the driveway. Still won't budge! (At lea…

Update 10/15/15! The Mopar1973man.com Cummins High idle switches are for sale again in the Forum store http://forum.mopar1973man.com/store/product/41-mopar1973man-high-idle-switch/ The Mopar1973man.com Cummins High Idle Kits are no longer sold through DAP.

I am wanting to start collecting parts for the conversion. So when I need to I can do the conversion. Spending thousands on an automatic rebuild doesn't seem smart. So what do I need? How big of a job is it? Weekend? Which transmission should I look for? I do want overdrive.

Installed raptor 100 about one month ago fuel pressure changes about every three days and has to be adjusted Up or down 3-4psi is this a problem with the raptor? If the screen on the inlet is clogged would it pump 42oz fuel at the vp in one cycle? When you set fuel pressure at 17psi at idle wot is 13 is that normal? Thanks Ed

I have been lurking on here for a while and just recently decided to sign up since I have learned so much on here, so this is my first post.Thanks to Mike and others on here-what a great site.I bought my 2001 XC 4x4 Auto the end of July and have been doing some work on it. It had 96,000 miles. This is what I have done.Installed MoparMan's puke bottle fixInstalled gauges-fuel pressure, egt, boost, transmission tempChanged all the fluids/filters and was pleasantly surprised at the cleanliness of the tranny pan.Installed the '08.5 and up steering kit from Mopar since I had a slack in a couple of tie rods.Alligned and balancedInstalled a FASS 95 with new lines to the OEM filt…

I was cruising down the highway towing the boat a couple months ago, set cruise on 60 and just started to slow down nice and easy. Since then, it has been out except I tried it yesterday and I feel it trying to take the pedal but it gives up. I am looking for any suggestions on an accurate way to diagnose if it is a vacuum leak or something in the servo. I look forward to your response.

I figured now would be a good time to change the fuel filters being its double the typical mileage. Stock is suppose to change out at 15,000 miles or every other oil change. Here is what the stock filter and the Donaldson P551315 looks like after 30,000 miles of fuel pumped through them.I must be getting clean fuel because I was totally expecting after 30,000 miles I would be look at a AirDog filter that was black and the stock filter about the color I see now. But I was shocked to see both rather light colored. Now I know to just use my fuel pressure gauge and look for the fuel pressure drop. Because both of these could of gone farther yet and still in good condition.

So here I am again.... When I'm driving my 5 speed, usually in 5th and highway speeds, I put the pedal down and the rpm's go up but the truck doesn't accelerate. It doesn't do it all the time and it does it mostly in 5th gear. I know this is probably an easy diagnosis but I'm no mechanic so let's here some ideas!!!Thanks in advance!!!

Finally got a comp for my 02. I'm reading the directions and I'm having trouble deciphering where and what wire to tap. " Top wire closest to engine block". Anyone know what color this one is? Stock VP the engine is an H.O. Also, the instructions say nothing about the ground wire, can this go anywhere? Where did you guys that have one put it. - - - Updated - - - Never mind, ten pages into the search someone directed me to the Juice installation page from Edge. Alot better picture than the Comp page.

can some one tell me if the turbocharger is ok to have side to side play on the blades. it dose not have end play. the blades do not seem to be hitting the housing the truck has 160,000 miles on it thanks Joe