2nd Generation Dodge 24 Valve Powertrain

i like my truck so much i got another one. its a 01 2500 qclb 4x4 5 speed, edge jwa,couple pillar guages, some kind of 400 dollar air box (going to change to a 30 $ bhaf just need to find stock boot), four inch turbo back, four inc lift (that has to go, might have questions about that) ,fass 150, 92000 miles. oh and looks pretty good all one color with a few small dings and scratches.i need to put a fuel guage in, why it doesnt have one with all the other mods the guy did i dont know, and new fuel filters in tommoro. so i should get good pressure to vp, but my very first question on this build is this,if i have 15 psi to vp, how do i know if the vp is healthy? is there a …

OK, I have a 01 2500 with 112k. FASS DDRP and HAD (took off today) an Edge Comp. Last week while driving 35 there was a miss in the motor and when given throttle the motor would miss, pop, hesitate and shutter. Pulled over, shut off the comp and shut down the motor. Restarted and while in Park idles and revs fine. When put into gear once the tach hits 1500 rpm it starts all over. When I unhooked the comp from the harness I got a CEL and P0237 and P0230 codes. Changed the fuel filter and cracked the VP44 inlet banjo to make sure I was getting fuel. It sat for a week and I had it towed home today. No CEL and I drove it into the garage fine. Unhooked the Edge harness complet…

So guys I apologize if I already asked this but I looked through my post and can't see that I did. I know where there's a 2001 HO with a 6 spd for sale but it's 2 wheel drive. What is the big difference between the 2 and 4 wheel drive in regards to the 6 spd. I'm having a brain wave of buying the truck and parting it out , selling the engine and rest of the stuff off the truck and keeping the 6 spd for a spare or parts for mine. Not sure how much the engine would be worth, 355 km on it but still running decent form what i'm being told.

I have not even began to locate my problem, but its pouring the rain so I thought I would get ideas from you guys in the meantime. I was working on my jeep down at a friends house last night, had about 3/8 tank of fuel and after sitting on a steep hill for a few minutes, both running and not. When I returned to my truck it was showing low fuel light and gauge was down past empty. I of course checked to make sure I had not had a leak or fuel line come off and I did indeed still have fuel. I thought it might have been just because of sitting on the hill, but the gauge remained below empty and light on for the entire 35 mile ride home, and I stopped to put about 10 more …

Check this out, never heard of this. Scroll down to almost the bottom of the page. http://hoeslidiesel.com/store/page2.html Connector,VP44 Injection Pump Repair connector for the VP44 injection pump. Fault code P1689(no communication between VP44 and ECM) is a common problem when this harness goes bad. Pins in this connector can wear out and not seat properly to VP44 pins. Why replace the entire $1,000.00 engine harness when you can replace the connector?

I was looking at the conversion kits for the front hubs, converting them to old school lockout hubs with real bearings....And they are claiming 2+ mpg increase...that is a big gain for these heavyweights. Is anyone currently running these hubs that could confirm this claim??

Hello Folk's new to the site hope i placed this in the correct spot. So I have a 2001 Dodge Cummins QCLB Dually with a 24 val HO 6spd 4x4. The truck has 180k mile's on it. When i bought the truck a few month's ago to pull trailer's with full time (around 100-150 mile's a day) for my then job but, have since changed job's and only drive the truck about 2 mile's to work. So my question is will it hurt to drive my truck such short distance's every day 6 day's a week. Will it hurt it or cause damage to any thing? During the summer i don't worry as much but we are seein' 15-20F night's here i do plug in the truck for a couple of hour's every night and allow the truck to idle f…

Has happened twice in the past month; Truck will not charge, Check Gauge light comes on. After 20-25 miles with voltage dropping <10; truck will start charging. No CEL, unable to pull codes. Readers do not connect to my DLC

Hey guys you know how or where I can get wiring harness for a Edge Comp for a 2002 Cummins. I have the unit but the wiring harness was misplaced while moving.

2002 dodge 24V 275000 no blow by I just got the truck a couple months ago. It had an edge juice on it at one time. It was removed before i bought it. Right after i got the truck it started acting up some times it would start other times it wouldnt. I ran some tests and the blue with a red tracer wire to the vp44 had power when trying to start the truck. It shouldnt so i cut it. All was fine and fixed. 2 weeks ago im driving and get dead pedal sometimes it would rev ok then it wouldnt. Put my code reader on it got 1 code p0122. So i replaced the APPS sensor. Ive tested the new APPS and its working perfect. Did not fix the truck. Did the key trick got 2 codes P0122…

I have a problem that is bothering me. I suspect the lift pump is going bad but I want to be sure before Idrop the money on a new one. This has been a rough couple of weeks and money is tight.I had my gauge acting up and bouncing all over (Glowshift). They sent me a new sender and all was good. Took it for a test ride and verified that I had pressure. Not real good pressure but 12lbs. at idle and 6 at WOT with the Quad on. Was talking to a friend and the pressure just dropped to zero. Power off type of drop, not gradual. Truck stayed running. Shut it down and restarted it and pressure came up for a little bit and then off again. Put a mechanical gauge on along with the el…

I'm preparing to check and repair my KDP. I down loaded directions from Geno's Garage. One question Geno's directions did not address was the removal of the Harmonic Balancer and Crank shaft pulley. I believe they are both Keyed and only go on one way. My question is "Do I need a gear puller" to remove them. Information will be appreciated, Thank you.

I did get it started, I jumped the terminals on the starter ('00 3500). Funny how you check to make dang sure it's in N before crawling under the truck... and still a little nervous when you stab the terminals with piece of baling wire..So, tomorrow, will check the fuse, relay, and the clutch safety switch... anything else?

Hello, new member, 1st post. Long time dodge CTD owner. Have lurked on many of the Diesel forums but never joined one. This one seems more laid back and relaxed then some I read info on. I just picked up my 3rd 24v 2nd gen truck a few weeks ago. It's a stone stock 98.5 24v, just had a reman IP pump put on it less then 4,000 miles before I bought it. I bought a 1999 brand new in the fall of 1998, I could write a novel about that trucks healthy appetite for lift & IP pumps and my experiences with cummins and dodge about it. But that is not a new story. No one had an aftermarket fix for those trucks back in the day when they were brand new, like a AD/Fass. …

Hey guys, Im wondering who has ever experienced an issue with the kdp on a 24v? Ive read of the possibilities of the problem continuing into the early years, but Ive never personally heard of anyone thats had the issue themselves. Has anybody experienced anything, either with your own truck or a buddies or a customers vehicle perhaps?

I have someone on the internet wanting to sell me a complete NV 5 speed gearbox out of a 1999 3500.I do not need (at this time) an extra gearbox but what he does have is a Gear Vendors overdrive attached to the rear end of the gearbox. Have been looking at a GV overdrive for a while now and simply cannot afford the $3000 price. EDIT This $3000 is for a new GV overdrive unit, not the used transmission!Any comments on if it would be worth looking at a 5 speed tranny even if it did have the GV overdrive with it? Personally I like the 6 speed box but would really love another high gear to lower my RPM's on the highway. If I did this could either swap the 6 for the 5 speed wit…

If they are not on the Michal's list all ready Gillett Diesel Service Inc. 14812 South Heritagecrest Way Bluffdale, UT 84065 http://www.gillettdiesel.com/vp44injectionpump.aspx Exchange ONLY NO Bosch 815 test bench on site and Orange County Diesel, Inc. 17242 Gothard Street, A and B Huntington Beach, CA 92647 http://www.ocdiesel.com/ Exchange ONLY NO Bosch 815 test bench on site

This is the second time my truck has done this. I helped a buddy pick up his newly acquired dodge dually and I had to winch it up onto his trailer. When I get done winching, the truck is idling at 950 and won't come down blipping the throttle or brake. I drove it 15 miles miles home and it was still doing it when I got home and every stop sign in between. I came in the house for a couple hours and went back out to reset the apps and cranked it before I did, it fired up and idled perfect. This happened last time I pulled a truck onto a trailer but I had to reset the apps to get it to idle back down. I guess this is a safety feature so the batteries don't get low?

Where exactly is the main ground cable located on my 98' 24 valve? And is there more than 1? My headlights are dimmer than congress:lol: and I was told to check my ground cable.

Since I have had my truck, the stock oil pressure gauge has not worked. The people before me installed a mechanical oil pressure gauge on the pillar but I want to put my fuel pressure gauge there. Is there any way to test the oil pressure sender? I just want to make sure thats whats wrong. The gauge in the dash just sits at 40 psi any time the key is on. I also have the code p0522. I believe that is for the oil pressure being out of range or something. Thanks!!! - - - Updated - - - I read through the p0522 code article already, I was just wondering if anyone had a similar problem with their oil sensor before. I am pretty sure its just the sending unit but I dont…