2nd Generation Dodge 24 Valve Powertrain

I may have a problem with my lp or fpg not sure. Yesterday I started my Cummins and noticed that the dash buzzer and wait to start light did not come on. The truck had been sitting for eight days without starting. After starting I noticed the fp fluctuated between 28 and 20 several times while at idle. Once driving it fluctuated between 18 and 24. The only thing I have done was changed the fuel filter when I serviced the truck about fifty miles ago. I installed a Donaldson ff. I believe I read that the Donaldson ff was 10 micro. I cant figure this deal out. Anyone had this problem before?

HI, I was reading the article on Fuel pressures for the VP44. I have a couple of questions. My truck is a 1999 and has 87,000 miles, the stock lift pump went out in 07, 57,000 miles and was retrofitted with a new lift pump in the tank, along with a new filter assembly. The truck was running good, the other day I stopped for about 30 minutes got back in the truck, started right up idled perfect, but stumbled above an idle, so I idled home, changed the fuel filter, had a very hard time starting it. I primed the system about 5 times before trying to start it, it finally started but real rough. The next day I rented a fuel pressure gauge, I have 10 lbs at the filter, I check…

I've got 1765 0743 0382 for codes. I looked them up but reading through the write-ups it really goes over my head! Could someone help me know where to start with pinpointing my problem? The reason I checked for codes is when I'm using my exhaust brake the TC always lockup in second. Sometimes does, sometimes doesn't. On the times that it doesn't lock I can force lockup with my mystery switch.

Hey Names Corey, been coming to this site for a long while now and decided to finally join in with this "new to me" truck I've had for about 9 months. I've had a few 2nd gens and actually never had any problems until this one but Im wanting to get in back into shape and see how long it'll go. Ive read the forums long enough to know yall like the sigs filled out so got that squared away from the start. I'm needing some help guys since this is my first cummins to have problems with there are a few things im still not certain of and if you need to ask me some questions to help me out let me hear them. First off, when I first got the truck on a trade the PO "said" it was …

I got a small refund from Uncle Sam this week and I am planning on installing a mechanical fuel pump. My question is whether I should go with the Assassin or Fuel Boss--what is the good, the bad, and the ugly of each. I know these topics have been beat almost to death but if you can point me in a direction of an article that has already compared the two that would more than suffice. I have searched through the different forums but I was hoping for a little bit more. Thanks,

I am looking to replace my stock fuel filter on my 98 dodge it developed a leak around the heater pigtail harness grommet and I am getting not much help from local dealer one mechanic told me to drill it out and plug it not sure if that's wise any guidance would be appreciated am leaning more towards aftermarket I am thinking suggestions please

I have a 1998.5 24 valve and I leak engine oil from above the starter. I leak about the size of a couple of quarters every night. Appears I have an early engine as I have a cap on the front cover. Anyone have any suggestions. Thanks, Philo

Ok, I my original transmission finally went out. So I replaced it with a Certified Transmission, the Road Ripper 2000. The uninstall and install of the new transmission went great. It shifts great and everything. The problem I am having is, I believe it is going into lock up too soon. When I am empty, and take off from a stop gentle, and gradually ease up to speed, sometimes it will lock up at 40 mph, which is no problem, but it dosent act like it wants to unlock when I give it a lot of gas. I have to put the pedal all the way to the floor and hold it there for about two seconds before it will finally unlock and I will have power. It unlocks fine when coming to a stop…

i apologize for starting a new thread on this beaten to death topic especially since i know the info i'm looking for is out there, ive read a few threads where moparman goes over a more foolproof diagnosis strategy for discerning between a dead pedal apps failure vs vp44 failure. after searching for the last hour and a half i can't find the threads or info i'm looking for. anyway my truck is 2002 ho 6 spd. 130k nv5600. edge jwa, with pressure gauge and egt installed and an analog fuel pressure gauge. ddrp mounted on frame producing 17psi at idle and no lower than 9-10psi at wide open towing heavy. ABOUT A YEAR AGO: so i'm going to paste some stu…

Hello All. I am relatively new to Cummins but have owned my 99 Dodge for a couple years. It has 265,000 miles on him. Everything is stock except the previous owner installed an edge EZ and I installed boost and an electronic fuel pressure gauges. When I installed the gauge last year I installed the t-fitting to avoid the hammer effect. I have a question. Here over the past couple weeks (it has been 0-20 F here) when I start up the truck in the AM the pressure will be in the single digits for about 5 seconds and then jump up to 13 or 14 psi. Do you think this is just because the diesel is cold, or is my lift pump about to quit? It is a stock LP and I plan on changi…

I am installing a new Edge Juice with Attitude in my 2001 Dodge Ram 2500. The kit comes with a new Boost Elbow, but my turbo has the hard line between the tubo and the waste gate actuator. All it said in the manual is that on some trucks you can't install the elbow. What affect will this have? I read something in a thread about installing a turnbuckle on the WGA, but when I searched for more information, noting came up. I am assuming that you are installing it on the rod from the WGA to the WG and using the turnbuckle to adjust the psi the WG opens at. Is this worth doing? The truck is basically stock, BHAF and 4" exh but no other HP mods. Thanks for any help …

while I am not certain I think I must have a leak somewhere in fuel system after my 98 truck sets for some time it will start right up like its supposed to then after 10 or so seconds will die then I must crank it 6 or so times to get it to start then it seems to be fine can any one elaborate on this symptom or problem Thank You

I have 196000 miles on my truck now and was thinking of taking it in to a mechanic to do a tune up on the valves and get the turbo cleaned. I am also going to have them do the thermostat to a 190 and have them go through my wiring on my column gauges and redo them because who ever put them in before I bought must not have done it the best way and took corners and might have them look at the a/c... just wondering if any other things I should just have them check on while its in the shop? I only want it down for like 3 weeks because I live in Bismarck and im taking it over to Jamestown because they have good rates and I know the people working on it has done good work o…

Do you use 15W40 , 10W30 , or even a lighter weight oil ? Did you use it based on some's recommendation or what the owners manual stated ? Not asking about Syn-oils , yet............

I've been looking for the MG oil and all I can find is the LE. Does it exist, does it make a difference? It's what's recommend for 24 valve cummins.

Hello all, I just installed a new Gearotor/Motor tower assembly on my Air Dog FP-100. While it was out on the bench, I noticed there was some debris in the pre-filter screen at the inlet to the water separator. It looks like disintegrated paper, I think my wife had the small cardboard seal in the cap of a bottle of fuel treatment fall into the tank months back. Now it has broken down and the fibers are clogging the screen. I have 1/2" fuel lines for the whole system, can anyone recommend a good in-line filter to cut into the pump supply line? I would like one that I can disassemble to replace the element and clean. Most of the in-line filters I have seen are for 1…

I was wanting a set of batteries for my farm tractor ...and. I thought it would be a good idea to buy a new set for my truck and use the good ones already in it to put in the tractor. I told the Interstate guy that I wanted group 31...he said no way will they fit. Sold me group 27s. Same rating as the ones in the truck although a bit smaller. WOW...I thought the ones that I took out of the truck were good, not so much compared to the new ones. It sounds like that air starter in the other thread. The tractor will start with the ones from the truck but not as good as it should. Warm weather is coming and things will be better for the tractor then. Regards Chris

Ok guys, I posted over in the CR forum about my brother putting a new turbo on his 05. So I am thinking about buying his he351cw from him, but I have a few questions. First off what is a fair price? 130xxx miles on it no shaft play. Second is it worth it for my second gen? My egts get out of hand quickly with the comp and smarty stacked. Will this cool them down very well? I can use his old down pipe if it will work. What adapters will I need for the oil input, oil return, exhaust manifold ect. When I tow heavy I turn the comp off and run the smarty on 9. Will this be enough fuel to spool the turbo? Any input is appreciated. Remember I'm in college and I'm on a budget!

Wanting to get a bit better mileage and maybe just a little more get up and go when I feel like it. I am a mellow driver but once in a while I like to step on it a bit. Nothin major. I have read about what some of you have done and here is what I am thinking now the truck is paid off. Assassin mech fuel pump, sounds like the electrical ones have issues here and there Big line kit Edge comp box Edge Insight CS Slight injector upgrade Now what I don't understand is what difference is there in changing the nozzles if you can just get whole injectors? Other than some extra coin savings. Plus any other input on what I have planned would be helpful. Steve

I am in the process of doing fluid changes, the truck has 234k and i have no idea on previous maintenance. I haven't had the truck long. I have heard not to adust the bands or do it every fluid change. What would y'all recommend?