2nd Generation Dodge 24 Valve Powertrain

has anyone bought a delphi fuel lift pump and if so how did it work and does it have enought pressure ? Thanks

I went aliitle bigger on my tire size stock was 245 75 16 went to 265 75 16 just wondering what my actual mileage would be right now im doing a little better than 14 arond townon the new tires also will the scan gauge 2 allow me adjust the tire size?

I was just wondering what kind of oil is recomended for my trans. I know what the owners manual says but what does that translate to at the parts store.

Any opinions on the WIX Oil Filter? I saw the WIX 51607 listed on Rock Auto for $6.71 each in a case of 12. The Fleetguards are getting crazy $ even if I buy them by the half-dozen, but still worth it I figure. They also have FRAM's but I don't think I'll put any orange filters on MY truck.I know I've seen a chart showing which filters other than the Fleetguard to use but can't find it now...

So, I decided I would give my injectors a little looky-loo. A few days ago, I did this. After fumbling around trying to figure out what wrench size the injector lines were, I got a wrench on them while the truck was running and all of them responded to them being cracked open. I was not able to get to cyl. #2 and #6. Is there a way to get to these injectors?Also, it seemed like it took a good amount of force to crack them open. I have never heard of a torquing device that would use an open-ended application like a wrench. How do I know if I tightened them enough or not enough?I have been avg. about 16mpg now after my BHAF install. I'm curious to see how my injectors are d…

Please help. I was driving home from a nearby town, and my CEL came on, all of my dash gauges quit working and the odometer says "NO BUS". When i got home, I scanned for codes and came up with these: -P1698 - No CCD, message fom TCM -P0383 - Generic Grid heater relay -P1687 - No mechanical instrument cluster BUS message -P1694 - No CCd message from PCM - Aisin transmission -P0122 - Low imput throttle position sensor circuit low imput - I replaced the apps 2 months ago with a Timbo unit. Any insight would be much appreciated! --- Update to the previous post... Any chance i have a bad ECM?

Hello all;I have a simple question, that may not be a simple job, but....I am in need of a new cab, instead of spending all the time cutting and welding new floors, rockers and cab corners. I have a really good deal in front of me, it is a cab from a 1995 ram gasoline, now I have a 2001 ram diesel, are the cabs interchangable for those years??? If so are there any suggestions to make my job go smoother, is there any drilling or cutting??? or if anyone has done it before what was the order they went in for taking things apart? Thank you very much.

ok diesels getting up there with whats in my sig and me running comp on 4x4 and driving like theres an egg on my skinny pedal what would be next? injectors? watermeth ?thoughts?

Posting this issue for KyCTD since we talked about it in the chat last night and told him I would type it out for him. Bought a 2001 auto CTD that ran fine. One day he started getting on it pretty good and then it just turned into a really doggy truck, slower than any stock truck. Described it as "Geo metro being pushed by a yugo with a 30mph tailwind lol". Found it also had a cracked block. Scrapped the engine and found a 2000 donor truck which was also an auto. Put the engine in using the 2001 ECM and it ran but something wasn't right. Found out the cams were different, switched the cams and that made it run perfect. He used the 2000 VP as well, not the one off …

Has anyone with an automatic trans had their transmission Heat exchanger (located on the passenger side of the block) fail?If so is this a prone part to fail?The reason im asking is that at 10 years, and 8 year old engine coolant(before i changed it), im wondering if it will stand the test of time, or if i should go about replacing it, and avoiding trashing my fully built transmission.

Got my sample back in PDF file form but cant figure out how to save it to post it up. I normally use photobucket but it wont let me on this.:shrug:Or I can email it to someone and you can post it.

Before I changed out the motor and tranny there were lots of spots in my driveway so it didn't bother me. But now there are no drips but I still get that burned oily smell once in a while. Being a rooky, is there something I don't know about? I can't see any obvious cause of this odor.

Was surfing the site yesterday and ran across a comment stating that it is not recommended to flush out the troque convertor when changing fluid?Why would that be a problem?

Hi guys. I have a couple questions on what is going on with my truck. I noticed I am shifting too early where the RPM's are low and it surges or jerks until the RPM's get higher. It is shifting into 4th gear with OD off at 25mph and it happens also about 45mph where its shifting into high gear and doing the same thing with OD on. Tonight I was doing a couple road tests and I got on it alittle more than usual and when I got home because of how it was acting, I used my scangauge and I had a p0234 code. So I have been doing alittle reading about the wastegate etc which I do not understand and wonder how the code is related to what is going on with my truck. Is it someth…

I am having a longer cranking issuse then i ever experienced ,I just had a airdog installed and now have excessive cranking ,now I have exchange a few sentences with one of the mopar members here and this is what I just did, 1st> the truck sat all night, went out unpluged the airdog turned key to start and it fired up about a 1 second or less crank,turned it off right away, 2nd> I plugged the airdog back in and turned the key to start without waiting for pump to prime it took about 1 1/2 seconds to crank over, 3rd my truck is sitting in a driveway with the front faceing up hill when it started the 1st and 2nd time I drove it for about 13 miles and about 30 mi…

My truck ultimately runs great. It has good power. I recently replaced a crankshaft position sensor and noticed the plug will need to be replaced also. However replacing the sensor only, the check engine light has not illuminated again.However recently I have started to get a miss at idle after coming to a stop. Very slight, but noticeable. You can feel it in the truck. Not similar to the hard miss the crank shaft position sensor caused. The weird thing is my AirDog 150 has also started dropping pressure pretty bad. When new it was putting out 17psi nearly constantly, about a year later it was at 15psi. Then it kept dropping, much quicker after that. Now it is at…

Ok Gang...I got the ScanGauge II dialed in perfectly and extremely accurate now. I know exactly how to do and make the adjustment so it right near perfect. Fillup Procedure.1. Pick a fuel station that you going to use for a calibration fill point.2. Pick a pump that you going to use for filling. You must return back to the very same pump in the same direction!3. Fill the tank on the lowest sped possible of the pump this reduces foaming of the fuel.4. When the pump shuts off. That's it! Hang up the nozzle! Don't round up to the nearest dollar...5. This you go through the fillup process but leave the setting alone. Don't change the offset percent. But you can change the pri…

Ate all the shims in the injectors the same diameter? It seems [MOPAR][/MOPAR]like it.

Thinking about installing a Boost Fooler with Boost Elbow on my 1998.5 24V Cummins. If I do this before I install the RV275 injectors will I notice any increase in power or fuel mileage?It's cold and very wet here now. When the weather warms and dries up I will do the KDP, RV275 injectors and valve adjustment with the Boost Fooler. What's your advise?Thank you, Kerley

Is there a way to tell if my Killer Dow Pin has already been repaired with the KDP Kit?Were all Cummins 5.9 24V 1998.5 manufactured with the KDP problem?Did Cummins ever solve the KDP problem during assembly?Any information will be appreciated, this KDP issue could be a very expensive repair which worries me.