2nd Generation Dodge 24 Valve Powertrain

Hey guys... I know you wanted to see the SGII and how I mounted...

Hey gang,Got a question for you. A friend of mine has a Smarty and was going to reset my speedo. Any way he tried it on his without the Smarty tune loaded on and it didn't work he said. Him and I were under the impression that he could reset mine and have the tune on his?? Does anyone have some experience with this??:shrug:Thanks,Winslow

Preempted sorry if this is in the wrong place but my truck has stumped me a little bit of history they came on about three days ago and it has no codes and it just randomly on my way home the abs and park brake light came on and the spedo bounced from actual road speed down ten to twenty mph then back up then down so on and so forth the problem isnt as noticable under thirty and its off until the truck gets on the road I have reset the computer by removing the negative cables then replaced them an hour later no luck so I removed them again and replaced the rear wheel speed sensor hooked up the cables and still no luck.the reason I put this hear is because for our trucks i…

I pulled all rockers off replacement head for my truck and what I noticed was every rocker had scratch marks in the bottom of each rocker and the rocker shaft, Is this normal? I dont like what I am seeing but there is no slack in them that I can feel, I will mic each one tomorrow. Can anyone give me the wear tolarance for this inspection? I did a search and not getting the right info. There is no sluge in head it looks good as far as that go's. I just cant belive the rockers would all have scratch marks like that. Oh and cylinder one and cylinder three had green dots far something I dont know what, cylinder one with one mark and cylinder three with two dots. Also stock t…

could you direct me to the ecm REMOVAL, OVERHAUL &INSTALLATION article

Do I need to replace head bolts when replacing head? And can I leave turbo conected to down pipe and leave it all conected on boost boot side?

on occasion, I have had a CEL, and the P 1693 code. I had the ECU codes checked, and it was the crank position sensor. The CEL randomly has appeared, and nothing has happened except in 2-5 starts, the CEL goes out. This happened again two days ago. Today, CEL came on again, and on the way home from work, the engine stuttered. just a miss of maybe 2 or 3 power cycles, but ran smooth with good power otherwise. I am unaware of how to get both P done, I've tried and only get one, with the P1693 code. How is this done?Am I finally having to pay attention to the crank position sensor? Any pointers?Thanks for the input.

I have 4 inch mbrp system and it is loud and drones all day long. I want a quiet muffler that will not effect performance too much. Any ideas?

I got the 47re auto in my 01.. the tranny is stock and runnin my tst powermax on high i can tell something is slipping.. How do I know if the TC is slipping or the clutch in the trans. slipping. What Do I need to do get a 3x TC or should I have it rebuilt and have a tc also.. Im looking for idea's on how I can beef up my tranny with out spending a ton.. Ive looked at ats tranny's and wish I could just get one of them but they want 4k for a stage 1 tranny.. Not sure my wallet can handle that with a 1600 core charge on top of it all.. So what do you recommend..I dont race so boosted launches is not happening, and I never tow over 15k lbs. I dont pull at truck pulls so that…

So JohnFak is on the road going from here to Arizona and he said yesterday it was flawless, not even the bucking issue he has talked about. Well today I think he said the bucking is back a bit but his edge juice display module is showing speeds of 60/90/100/120 just bouncing all over the place. Speedometer is reading steady 60mph though. The RPM and throttle % on the EDGE also are steady, so nothing is messing up but the speed it is detecting. He is wondering if he should reset the APPS or something. I am not sure but I think each thing the EDGE monitors has it's own sensor? I remember there was a ton of wires all braided individually. Thought the speedo…

ok guys i found a great website that has tons of info, specs and a bunch of other stuff. heres a link https://quickserve.cummins.com/info/index.html this website is FREE!!!!!!!!!!!!!!!!!!!! all you have to do is create a login and your up and running. enjoy

Ok Gang... I've seen a bunch of you wondering about needle valves... Well here I'm going to explain the reason and why needle valves should be used on all fuel pressure gauges including electric gauges. Now first thing first is why do we need a needle valve? Well the needle valve is a adjustable damper for the fuel flow. It prevents harsh or water hammer pulses from reaching the gauge or sender. What is water hammer? http://en.wikipedia.org/wiki/Water_hammer Here is what the pulse looks like... But now figure that is pulse open and close at half the RPM's but for 6 cylinder. This pulsation with eventually wear out or eat the gears…

Is there any diff.

Has any one converted there front ends to the old style lockouts so the front end don't turn all the time and if so were do you get the kit? --- Update to the previous post... here is a link i found http://www.emsoffroad.com/store/index.php?main_page=product_info&cPath=128_131_134&products_id=330

Well i bought my 2001 dodge 2500 quad cab 4x4 about 1.5 months ago and have already replaced lift pump, vp44, and radiator clean from puck bottle. Last night i was in my way home and front wheel bearing went out, dang near lost a wheel, that was another $300.00 for a part. so i checked thr other side it was good and i will change it in a couple months due to money, any way took the other side aprt to check and grease the brakes pins and guess what no pin bushings on one side and dry as a bone with almost new pads. I don't understand how people think there mechanics and not do the job correct. Now the question the abs light came on when the bearing came apart and now the l…

After close to five months of people looking at my truck and not being able to fix it - It ran tonight!!!!!! It was the VP44, and so far everything seems good. I cant drive it yet tho cus one of the geniuses at the one shop picked up the front end of my truck with a fork truck and it crushed the steering stablizer, its another $40 which is really nuttn compared to the cash i forked out for the VP44 LOL!!!! Im just so happy its running right now tho nuttn can crush my buzz LOL!!!! I want to thank you all for the help, you all are really great!!! Ill let you know how it goes from here, and thanks againg for you all being here!!!

First question isIs there and ground wire going to the sending unit in the tank for the fuel guage or any reason my gauge would read steady, but incorrectly? Before I had my box off and had my truck painted it seemed like if I was abuot 1/2 tank i could fill it for about $90 +- and now it seems like it takes more as if the guage isn't reading right. Today i put $92 in it at a little less then 3/4 of a tank showing on the gauge. The gauge never jumps around is if anything is wrong :shrug:Second question isAfter I put new intercooler boots on I fianlly noticed being able to hear my turbo spool up. Last week it seemed to get a little louder sounding then usual, had it for …

HeyDriving today on highway - and around 60mph the truck starts to 'buck' gently like its missing fuel ?? Pressure gauge says 14 @ WOT and 16-17 regular.Me and ISX just put the old injectors out and put the oem ones back in (for the stall issue). It doesn't idle rough or appear to be missing (assumming missing in a diesel would sound like a rough idle/egnine etc).Not sure - Might stick some 2 stroke in it tomorrow - could one of the injectors be plugged/partial blocked ??

I was cruising down the highway today and the truck acted like it slipped into nuetral. After that there was no go. None of the gears works, forward or reverse. At the time of the incident my temp was normal and there were no wierd noises. There was no noise when it went eiher. The truck just reved like it fell out of gear. My only guess is that I broke the input shaft. I assume that the only real answer will come by taking it apart.

Here is my oil sample results. Not bad for 8k, and it says it can go more. OIL Analysis 100910.pdf