2nd Generation Dodge Reliability / Performance

quick question ..does any one know at what point the stock turbo hx 35 i think needs the waste gate hooked back up if at ? i havent made any huge performance upgrades yet ..just a few minor ones but i know at some point i will need to think about getting the waste gate working again to keep the turbo safe

Ok guys I have 315-75's on my truck and I believe that my mph is off about 13% so if i am trying to calcuate my correct mpg would i take my total mpg' per tank and multiply by 13%??? :shrug:If i am thinking right this should give me an accurate mpg. Any help is much appreciated.

I have 130, 000 miles on the truck in my sig with the stock transmission. The transmission doesn't seem to be slipping, but if I upgrade to 100 hp sticks can I get away with just a converter and valve body from a reputable company like dtt.

Photobucket Album

Look at this neat video that I ran across!!! I wonder what it takes to complete this swap??? Sorry I'm not sure where this is suppose to be posted but it is neat!!!

I am sitting on thew side of the road with no power. every thing works but the engine want run. it just shut down while driving. I have a p1694 and that is all. any body got any ideas of where to start?

First off hey all! First post and coming over from CR. Seems to be the more techy minds here. Ok my question is with tm and the smarty. Hopefully I can explain in words what's going on in my mind. Best way for me to describe smarty is it seems to shorten the pedal distance for the ECM to determine wot. My concern is with the auto trannies. Being that more power/tq is produced at less pedal movement, would the tranny not suffer from less tv pressure meaning less line pressure and lower clutch holding ability? The first years of 24v did not have tm so how did the transmissions deal with this? Is the bellcrank for the tv cable different or the lever on the tranny indexed dif…

When I purchased my truck, it came equipped with a performance tuner. I didn't know what it was, what it did, or how it worked.I later found out it was a Quadzilla, not sure exactly which one. Must be one of the older ones, because the one I have, I couldn't find on their website. I started messing with it and realized none of the features I had set would work. Now, I don't know how many of you know much about these Quadzillas but, i'm debating on wether or not I should keep it on the truck.Under the hood I found a disconnected EGT sensor. I don't know if it belongs to the the Quadzilla specifically, or if it's factory. But, it could be why nothing on this thing works, wh…

Which Kit do you use ? How useful do you find it ? Worth doing ?

Gang, I got to looking up latter and traction bars and came across these: http://www.tuffcountry.com/miscellaneous/traction-bars.html I was wondering is anyone is running a set and if they do anything?? I like the idea of them not hanging down below the frame and they are pretty cheap. I don't plan to race/pull on a daily basis, I just want to help with the hop when I play around every now and then. Also might help when pulling trailer? Any feedback would be great!! Thanks, Winslow

http://www.competitiondiesel.com/forums/showthread.php?t=88662

Hey,I was curious...I have a BD Power box which has levels up to 5-5. It is just like the Edge Comp. I was curious if Edge can make it "hot" like the Comp Drag to keep fueling up to the 3200 rpm range??? I have been told it the same as the Comp but different label because BD Power bought some of these boxes from Edge and slapped their name on them. Does anyone have any idea? Thank y'all

Where is the data link connector to hook up my edge comp? I've spent a lot of time looking but no find. Is it a loose connector or is it connected to something and I have to disconnect it? I did find a loose 4 pin connector but it does not match what the comp came with.

I'm planning to add an XZT+ before towing season. I really need to upgrade the lift pump before I get into towing again. So I'm weighing the options vs cost. I'd like to do this once... I'm not going racing but need to tow properly... can never be sure what that'll take until I've done it. Airdog vs Raptor?Should I go for the draw straw & big line?Russ

Installed a 0-30 psi gauge yesterday. I tapped into the filter housing; the '99 has two 1/8" pipe thread ports on the top of the filter bracket, inboard port is post-filter. I used Mike's recommended Weatherhead needle valve feeding into a tee; pressure line to one port, Kohler engine oil pressure switch (NAPA SME 2509927S) to the remaining port to activate a low pressure warning light. Good news is all works well. Bad news is low pressure (big surprise here,eh?); 10 psi engine not running, 7-8 psi engine idling, 5 psi around town & 65 mph cruise on highway.Solution is not all that clear. Presently the truck is stock, 173k miles, seems to run fine, no starting proble…

any one know if 04 tow mirrors willfit on a 98.5 ? both are powered and heated....

Help ......ok heres whats going on need to fix my parking brake and fast have a vehicle safety inspection comeing up on next thursday ......gotta have a working parking brake .....i remember reading somewhere ..sometime that the stock parking brake was very weak at best on these trucks ....there was a way to make them stronger had something to do with turning the big spring in an opposite direction and welding a bolt in somewhere ..or something like that .....any one have any info on this? .....also any one have any helpful hints on installing a new raptor lift pump i just got mine in the mail today with the new 1/2 inch lines with quick connect fittings....thanks in adva…

Been reading up on the problematic OEM lift pump & aftermarket solutions. I have to say I'm a bit confused as to why the aftermarket pumps have a relief valve. I can understand that there needs to be a return to the tank from the lift pump to dump the air that has been removed from the fuel. But doesn't the OEM fuel system have a pressure relief valve that maintains supply pressure, and bleeds the excess into the fuel return line at the injection pump? Also doesn't the excess fuel used to cool the IP? If the pressure relief valve on the LP opens up, what happens to the required extra flow to the IP? Is the OEM pressure relief/return system overwhelmed by the aftermark…