3rd Generation Dodge

So Im having trouble with my rebuilt 48RE transmission to go forward or backwards. I got a shift linkage ordered and on the way just need of yalls input on what do yall think could be my problem.

2005 dodge 2500 5.9 6 spd 4wd banks intake. Had a no start for a month but gas rag worked. Was p0251. Buddy of mine has a shop, would let me know. Over did it and pinned the tac-clutch went out. So no start and no clutch.Took another 2 wks to get a bay open to work on it. Got one open so started in gear to drive to shop (speed shift) but after 25 miles she just quit. Towed 2 miles to shop. Had a ton of codes put new regulator in. Still no go and a p0016. Cleared and it reset but no start. New cam/crank sensors New pressure limting-still no start. Been going through the harness but no bad wires yet. Losing my a__. Trying to fix myself. I day work and shoe horses and…

I'm stuck probably going to need a tow. Here's the deats 03 3500 dually mostly stock besides air cleaner muffler delete. Problem started as slow cranking condition so I replaced the batteries and got no where come to testing the starter I find that to be over drawing. Went to make it home so I tried to restart the truck. Long short cranked super slow then I heard a pop and the truck is completely dead red light on the dash ( it's on the upper left side of the coolant temp gauge)no interior lights no nothing. At this point I have verified voltage at 13.45 even on both batteries checked the fuses to find again no resolve at this point for the las…

Well after extensive “research” and two new APPS or TPS sensors I believe I have finally found the culprit. It turned out to be the connector itself. As I was searching for grounds I noticed that the pins in the connector were loose and moved around just a bit. After finding no short to grounds I decided to remove the pins and expand them a bit. Put it all together and it actually allowed me to clear the codes this time. Just took a short drive and it seems to be just fine! Has anyone else seen this problem and does anyone know where to get quality pigtail connectors? This was on my 04.5 2500 6spd.

Hello,I recently had a no bus messegepop up on my odometer in my 04 ram 3500 DRW 4x4 auto.all gauges quit working but truck still drives fine? Running lights and headlights are turned off but are all on still?ABS,BRAKE,and CEL are on and a/c dont work? Any help be appreciated!!

2007 ram 3500 5.9 Cummins. Driving home everything fine all of sudden just cut off check engine light flashing and won’t even turn over. Also no gear numbers lighting up. Just had transmission put in a week ago but everything has been running fine?

2011 Dakota here with the DTC p2245(o2 sensor 1/1 ref voltage low) thats been on here even after getting a new sensor. It’s probably one of the connectors or the ground circuit, but does anyone know where the first place to check is? Tryna save us some time here thx.10.0.0.0.1 192.168.1.254 happymod

Hey guys, something I have noticed with this '05 truck is that when I am towing and trying to take off I get a slight shudder. It doesn't last long maybe until 10 mph, but I do feel it. I was looking around and something that caught my eye was people were saying the shudder is caused by the two piece drive shaft. Anyone heard that? I know that on the second gen trucks a 1/4" spacer for the carrier bearing helped. Do you suppose I may try something like that? If I did, it might be a few months until I would find out if it helps.

The tilt wheel on my 2004 3500 is no longer working, it’s stuck in the all the way up position. I have watched a couple videos and know it’s the plastic part on the column that is broken. I can’t find the part anywhere? Can anyone shed some light on this?

I have a 2008 Dodge 3500 6.7, 6 speed it has been deleted but not tuned so the check engine light stays on. The issue I'm having is I went to get in the truck a few days ago and it wouldn't turn over, I have all power to the dash an when I turn the key the radio goes off and it won't do nothing. I did replace a battery end connector that was cracked. Replaced it and still nothing. The clutch safety switch is by passed also by the original owner and it did great when I got it, started fine an everything. I also did notice a lighting bolt that came on on the dash but now it's gone. Has anyone ever had this issue? Need help

i guys, I bought an 06 5.9 3500 stock, manual 6speed with 241000 miles in January (at the time - 257000 now) , so I'm still not as familiar with it as I am my '01. When backing off the throttle going downhill (usually) I sometimes get the wait to start light appearing and the ten dings... BUT not loss of power (no limp mode). It does not seem to affect anything. Sometimes it clears after shutting down, sometimes not. I have a ODBLX with Torque and ALFAODB (altho I have not yet paid for that app), and no codes other than P0633 Skim key code show up. I also have a UltraGauge and monitor fuel rail pressure (about 7000 at idle, and never more than 20,000 at speed - which …

I have a 2004 ram 2500 slt 5.9 automatic. Truck has ABS code 84 Vin Mismatch. ABS and Brake light are on and of course ABS does not function. No other codes in the truck at all. Every place I have called which repairs ABS modules, says they can not repair that issue. Chrysler discontinued the part. Supposedly it needs programmed. Local dealership said they can not re-program the ABS module. I have read you can swap it out with one from another truck as long as the part number is the same. I pulled one out of a truck my neighbor has and the part number is the same. Issue is still present. Anyone have any input on how to resolve this issue? Checking …

Hello im from panama and my truck was stolen but i get it again i have a power commander pc 30 but they cut the wires and take the pedal ?and other parts my problem is i have the power commander but i want to connect with my truck but i don’t know how the wires color going if somebody have this system and can send me pictures Please

Greetings! We’ve published a new Smarty UDC software version (1.1.13). This offers improvements connected to comparisons and Smarty UDC microSD card stability with old Windows OS. A complete list of modifications is present in our web site. SmartyResource--Home Thank you! 10.0.0.0.1 192.168.1.254 hotmail.com

I took some pics as I did mine last week, and thought I'd try making a write up on it. Basic tools etc. you'll need are , approx. 8qts. of ATF+4/filter,Governor press. solenoid and transducer,1/4' drive torque wrench, 1/4" & 3/8" socket sets, basic metric wrench set, a pick or small screwdriver, a drill with a 1/2" bit for the drain plug kit, big catch pan:thumbup2:, and a paint pen or sharpie,plus whatever I forgot:ashamed: 1) Drop pan to drain the fluid, the easiest way is to go around and loosen them all just a turn, then work from one side loosen the bolts in steps. The idea is to get the pan to drop on only one side to minimize spilling and dump the f…

Question - Do you lube your lug nuts or not? If so, what do you torque them too? I have always used anti-seize and torqued them to 135ft lbs. But last weekend I was going down the highway and my front right tire decided to pass me up. All 8 lugs were ripped out, and it looks like I had over torqued them. I realize wet the torque should be reduced, but never had a problem until last weekend. I have a 2007 2500 megacab and the hubs are ~6 months old with ~5k on them. Any suggestions? Thanks, Philo

I have a 2006 ram 2500 5.9 cummins. Engine ran perfect until I had starter and batteries replaced. After that I was getting a code on banks 6 gun tuner saying fuel rail pressure sensor voltage out of range. Then it started surging from 1k to 3.5k and nearly caused me to wreck. Snap on diagnostic showed 1 injector was weak so I bought that and it cured the surge. The mechanic recommended I have the ecm flashed so I took it directly to the dealer and they flashed it. After leaving the dealership when you hit the go pedal hard I had spark knock and it was smoking bad. Had the mechanic ride with the diagnostic equipment and acceleration I'm showing negative 7 degrees timing. …

What's everyone using for scan tools for step by step diagnosis and fix steps.

seeings how the two other two stroke posts are locked i am starting this one. http://www.fuelexpert.co.za/2strokeoilindiesel.php http://www.fuelexpert.co.za/2-stroke-oil-in-diesel-technical-study.php thoughts....

Here are some pictures of a Derale 15870 cooler that I installed for a customer. I haven't installed any of the wiring in these photos, but the fan will be controlled by a relay. The temp switch is on the inlet side of the cooler, and will turn the fan on at 180 degrees, and back off at 165 degrees. Here is the cooler (which is massive) and the bracket that I built to mount it to the frame. And the bracket mounted to the frame... The cooler mounted to the bracket. By mounting it at an angle, I was able to tuck it up against the bottom of the cab nicely, but not have anything hanging below the frame rail. Another …