2nd Generation Dodge 24 Valve Powertrain

Ok, the other day I changed the oil and filter and every other oil change I change the fuel filter. This time I notice a litte dirt inside the housing so I drain the housing and clean out the dirt. It was cold out so I left the fuel bowl empty. In the past I've just filled it up to the top of fuel stem and rolled the key a couple of times and it would start. I forgot to fill the fuel bowl back up today and just rolled the key, and now it won't start. Pulled the filter and the bowl has fuel but it won't fire. I seen an article on here before about loosening fuel lines in a certain order but cannot find it. A little help would be appreciated.........

Around 2000 rpm upon acceleration it sounds like I have a boost leak coming from the back of the engine in the center of my dash. The head gasket isn't noticeably leaking anywhere and my coolant level is good. I replaced the intake horn gaskets, intake manifold gasket and put new intercooler boots on. I'm thinking the head is lifting, due in part because I swapped my HY35 for WH1C with an aftermarket wastegate set at 35 psi. And no gauges...yet...maybe it's just more air sound I don't know, wastegate?. Any thoughts?

Not too worried in fact I kind of like it but I'm wondering what causes my problem. My TC doesn't unlock when I let off the throttle. Go on the brakes and it works OK. when it gets down to about 20mph (in 3rd) it unlocks by itself and sometimes if I blip the throttle it will unlock. It's like having a free ATS Copilot. It did this awhile ago and then cleared up for a year and now it's back. Shifts fine otherwise. I'm thinking APPS or something throttle related. Any idea's?

I was on my way to vist my brother today and while accelerating the clutch slipped in 5th. I realized my toe was on the clutch pedal and removed it right away and let off the throttle. Got back in the throttle(about 75%) and it slipped again. Did this 3 times in a row. Got done with my visit and took off to my daughter house. I had to drive across the mountains from Hickory nc to Johnson city Tn and never slipped the clutch once and I was trying to. The valair clutch is about 2.5 years old with about 65k on it. Anybody ever had this happen to them? It was strange,

Who has had Delay in "Wait to Start" light , delay in lift pump run when ignition is turned on ? My delay seems to be about 4 seconds. Once the Wait to Start light comes on my truck will fire right up. What was the cause and fix ?

My truck usually fires right up '99 4x4. 160k miles It started cranking longer a while back, but if I turn the ignition on and wait a few seconds for the lift pump to start it will fire right up I thought it was the fuel filter heater grommet Oring(stock fuel filter). slight seegage Well I finally resealed the grommet. But I still get long cranking if I jump right in and try and start, unless Im patient and wait a few seconds for the lift pump to run then it starts right up. Went over the whole truck fuel fittings checking for leak/seepage, top fuel tank etc. Everything looks clean and no sign of leaks Truck is stock, has all gauges, fuel press, boost, t…

I have a 2001 Dodge Ram diesel 4x4 that has developed a transmission fluid leak at the transmission cooler line to hose "quick disconnect" connection, once I finally got the connection apart, there is an o-ring inside the hose side connector. Is the o-ring available and where? Anyone have the part number for the hose line with the connector, I have searched and cannot find a part number. I prefer a good quality part, as it is very difficult to get to the trans cooler end and I don't want to have to replace it again. There are two hoses and I can't remember now which one I need, I think it is the hose closest to the driver side, but if I had both part numbers I could fig…

I replaced my water pump last year. It is leaking out of the weep hole again. The thing is when I was trying to check I didn't see anything come out of the weep hole. I could see where it had leaked out of it, there was evidence of it at the weep hole. There Is antifreeze under the pump that pooled there. But when I get the truck to temp and watch it I never saw any leak.Would the pump just leak intermittently? It just seems to me if it is going bad it would leak all the time. Is there anything else that would cause it to leak from the weep hole besides the pump goin bad?My truck is a 2002 6 speed 4x4 Thanks to anyone that can helpJason

I can't find my earlier posts on this... Every once in a while, the truck would not more than grunt. I'm only using it intermittently every couple of weeks. I have a 1.8A solar trickler on the dash into the always on lighter plug. The thing is, a hour on charge or a jump will fire it right up. The batteries don't seem to take much charging to spin it over. My first thought is dirty connections. We caught a nice warm day yesterday & I cleaned all the battery terminals with wire brushes. They weren't really bad as I have the treated felt washers under them all. I did see a spot on one that just looked a bit oxidized. I found one terminal (Pos on Driver's…

When I tried to start my truck this morning the WTS was flashing. The truck will crank but will not start. I think it may be the ECM. The fuel pump will not run when i bump the starter, but will work off the battery on a switch. I have checked all relays, fuses and battery connections. There are three codes P0123, P17656, P1694. Does anyone have any ideas what else I can check?

ok heres the case after my recent lift pump failure i have decided to save up an hopefully invest in i fass fuel system prob a fass 95 my question now is with this system my concerns are the pick up tube and stock filter housing does the kit come with the filter housing to vp big line also are these kits effictive with the factory pickup tube and stock filter housing or are they too restrictive to support the 600 hp they say the pump will support

2000 PPUMP 4x4 Pulled batteries to put on charger last nite as well as radio to install a new one.Both batteries 12.4V ....Truck wont crank at all - not even try. Starter fuses and relays look fine/ Switched them around with some others in PDC and no difference. Ideas on what to troubleshoot ? Had same issue when I came back from holidays. Pulled starter and it checked out ok and switched fuse and seemed to fix but fuse seems ok. thx

I recently bought an upgraded vp44 from Blue chip diesel ($1600) because my original died. After installing the first pump the truck started right up and ran great for about 10 minutes, then I got a code saying injection pump timing failure. I talked to Chip and he sent me another right away. This second pump has been great for about a week. Now for some reason around 1,000 to 1,200 rpm when I mash the go petal it loses power, makes a horrible lugging sound then picks up and runs fine. I am also having trouble starting. Warm or cold it doesn't like to start on the first crank and sometimes it won't start on the the second. This doesn't happen every time I go to start it t…

So just a general question I have an hx35 want a good filter was wondering if putting a cold air filter directly on the turbo would be good or bad seen a few around need some opinions thanks

Just wondering if anyone has used these gauges? I just received fuel and egt gauges. They seem like nice gauges, they have a high and low warning light and they are not overly expensive.

Well I got my ISSPRO 3 gauge pack in and I got it installed. I ran into some problems but gave Michael a call and he helped me sort some things out that I wasn't paying attention to. I ran out of time at my shop and daylight but went on a test drive at the airport and Airdog 150 is holding rock solid 18psi at idle and 15.5psi WOT in 4th gear pull. I am also pulling 21psi peak boost on my stock truck and I think that is pretty good. All in all I am really happy with the Airdog and the ISSPRO gauges. I will try to finish up the EGT and lights and maybe a video if any one is interested tomorrow. Thanks again Mike!

I bought this truck about 5-6 weeks ago so just now finding all the bad habits. So only one time a day (mornings) the oil pressure gauge wont come up, check gauges light comes on. So I turn it off start it back up and its fine the rest of the day. At first I thought trash in the sender but its every day. Oh and its the 5.7 Hemi

The other day I smelled a strong smell of diesel fuel and I pulled the truck over. When I looked underneath the truck there were over a dozen driplets dripping off the driver's side frame rail. The frame rail was completely wet. Diesel was also dripping off the transfer case skid plate. I recently installed a Fuel Boss fuel system on my truck. My first thought was maybe one of the new rubber hoses chafed on something, even though I was extremely careful on installation. I determined the leak was between the tank and the frame rail. After several drips of diesel fuel on my face, trying to peek in the gap between the frame and the tank. Since I was on a road trip an…

Fellas, is it going to screw anything up computer wise by taking my both batteries out for a few months? I lay my truck up would like to take the batteries out and trickle charge them all winter. I store it to far away from a power source to leave them in with a trickle charger on them while in the truck

Hey folks, This is my first winter with my Pacbrake. It had run flawlessly until ambient temps got down to around 10 degrees. Then it stopped working on my way home one night. The next morn. after I warmed the truck up for an extended period, it started working again. This cycle went on for a couple of days, then my 30 amp compressor fuse blew. I replaced the 30amp with a 20 amp. ambient temps are now around 32 and she's back to working reliably. My compressor is located by the passenger side battery as directed in the pacbrake instructions. I routed the air intake filter to the firewall behind my Bhaf. I have not yet remote mounted the actuator piston vent that pacb…