2nd Generation Dodge 24 Valve Powertrain

Just got my edge juice w/ attitude CTS installed and was wondering what the safe temp ranges for Trans. and egt's are? Truck is a 2001 3500 24v w/ auto. I could not use the supplied boost elbow either. Will that affect much? Should I be concerned with any other temps?

Did a throttle chop as check gauges light came on voltage reading zero. Got to job site checked cables fuses restart truck and voltage reading well under 14 but not tripping check gauges light. Alternator has 334665 miles on it. Anything else to check before I replace it. If I do replace it should I keep it to have rebuilt. Or turn in as a core. I'm in Star idaho closest place to me is NAPA . Thanks guys.

All this talk about bad alternators makes me nervous about jumping other vehicles. Is there a SAFE way to do it?

Had the 5th gear retainer nut installed by my local shop about 6 months ago and now 5th is hung in gear. Just returned from that shop and was told they can't see any problem from shifter section on top of the tranny so it must be internal. He told me he shouldn't have to pull the tranny since 5th is in the tail section, that just means a little less in labor. This 5th gear is starting to $500 here $500 there me to death. He hasn't pulled the tail section off to see what exactly the problem is but I am sure it want be anything to do with the retainer nut because that is what he put in and said I would never have the issue again. So far he is correct I haven't loss 5t…

New to Forum. Saw the Scan Display II in the article about MPGs. Where is the best place to get one price wise?Mohok

Owners manual, didn't want to wade through entire 60 page manual, (unless I get one) Question...Can I use this in my 2nd gen most of time but also move it to a different car when I want? Or once you program it for a certain vehicle, that's it? Question...Do all the features advertised work on 2nd gen's or do only show some, because of (age, or type of vehicle)? Question...Would you buy another? If I'm going to get something like a Quadzilla someday , is getting scan gauge worth the money? don't some features overlap? Thanks

man, this thing is AWESOME, so many different parameters can be shown, i found out from it that my TPS needed to be reset, so, i did that....also, for w/e reason, at idle, the MAP thing shows like 30, i don't know if that's good or bad...:confused anyway, here are some pics of where i mounted it and a couple vids of it in action... LOVE that fuel mileage... :hyper :D vids..... gotta wait about a week till i get to around 1/4 of a tank so i can calibrate it all the way right....

Installed Scan Gauge II and ran the setup. It gives me a 7.5 to 8.0 MPG while towing. My actual MPG was 10.2. Any ideas on what to do? Also, when towing my T/T (8800 lbs) into a slight headwind, I can barely maintain 60 MPH with the pedal on the floor. Is this normal? See signature for vehicle specs.ThanksMOHOK

Why would a scan on my truck 1998.5 dodge 3500 24 valve pull up Mercedes indo

Okay, just tried the scanner we have at the store here (innova 3100), and it won't read my truck. What are you guys using for scanners for our cummins trucks?

I have a scangage II that I use as a monitor and want it to display my oil pressure. Has anybody been able to get it to read the oil pressure from the pcm. I haven't been able to figure how to get my truck to show at the bottom of my posts so any help would be appreciated so here it is 1998.5 stock except BHAF , ISSPRO A pillar gauges , 4" exhaust , BD boost fooler waste gate line plugged

Hello All I have a Scangauge. I am wondering how accurate the boost reading is compared to a mechanical gauge. .....edit.... Ok, I just had another thought......So let me backtrack a bit.....I just bought a PowerPuck and an Quadzilla boost fooler (it plugs inline with the MAP sensor). I also just made a adjustable boost elbow and I do NOT have a mechanical boost gauge. At this point I have been watching my boost pressure via my ScanGauge. As my truck is unmodified the need to watch it at this point is for curiosity and MPG reasons only. I am planning on installing the newer goods today/this weekend, but I am now wondering if the Quadzilla boost fooler will alter my Sc…

Hey has anyone had problems with reading error codes with a ScanGauge II? I'm kind of wondering about this. Being that I got one and had a guy stop me and ask about error codes on his 2001 Dodge Cummins. Well I did the scan with the SG II and came up with only 1 code a P0216 (yeah the death code). But the owner asked me if there was a way to do it without a scanner? So I should hime the key trick... Guess what??? The SG II missed a bunch of codes!!! PPCU - P1693, P0500, P1682 PECU - P0522, P0523, P0216, P1693... :ahh: Felt like a dumb arse standing in front of a guy with a tool I swear by that missed the entire boat load of codes...:eek: So have any of you had this occur …

Ok Gang...I got the ScanGauge II dialed in perfectly and extremely accurate now. I know exactly how to do and make the adjustment so it right near perfect. Fillup Procedure.1. Pick a fuel station that you going to use for a calibration fill point.2. Pick a pump that you going to use for filling. You must return back to the very same pump in the same direction!3. Fill the tank on the lowest sped possible of the pump this reduces foaming of the fuel.4. When the pump shuts off. That's it! Hang up the nozzle! Don't round up to the nearest dollar...5. This you go through the fillup process but leave the setting alone. Don't change the offset percent. But you can change the pri…

Has anyone else had trouble with their display showing black boxes where the letter or number should be: Mine does this intermittently. If I unplug it and plug it back in, the display returns to normal. Also, some of the time it doesn't connect automatically with the truck. The gauges show no data. I have to unplug it and plug it back in for it to connect. Sometimes I have to do this more than once. Most of the time it works perfectly but these two problems are annoying. I emailed Linear Logic and they said to send it in for repair. I just want to make sure these aren't common glitches that aren't going to go away with repair. Not ba…

Ok gang... More updates made to the site... I drew out some basic schematics to some basic projects that are fairly common. I posted them over on my static pages so they won't get lost... Backup Lights http://mopar.mopar1973man.com/2002%20Do ... lights.htm Edge Comp Smoke Switch http://mopar.mopar1973man.com/2002%20Do ... e_comp.htm Fog/Driving lights http://mopar.mopar1973man.com/2002%20Do ... _lamps.htm High Idle Fooler http://mopar.mopar1973man.com/2002%20Do ... h-idle.htm Enjoy the information gang! :thumbsup

Vulcan performance no longer includes a FP test ports or Schrader valves with their big line kits and no longer wants to deal with customers as per our last fridays conversation with Eric. Even though Eric said he will make up an invoice for me to pay for one on pay pal...... he did not do it. I am very disappointed and the conversation we had was not like the good old days of dealing with him that started 10 years ago. In that time I have bought injectors, two big line kits, two lift pumps, draw straw, BHAF and an injection pump over the years. He obviously disappointed with dealing with the public, but still his word should be good as gold. Does anyone know …

For a long time now I have been contemplating better filtration for my truck as it is still using the stock filter housing.....post assassin pump. I have been wanting to purchase a VP max 3 micron dual remote filter kit from vulcan to take care of this and keep the pump clean and debri free also. I just couldn't pull the trigger as it seemed something more important always required my attention. As I cruised through craigslist the other night I stumbled upon a fella selling a brand new setup still in the box and plastic wrap. He had purchased it for his common rail, but ended up buying a FASS after a lift pump failure. He no longer needed and the price was right..…

Morning guys and gals, over the weekend my brother and I put a new head gasket and arp studs on my truck everything went smooth while I was bleeding the cooling system I noticed that a screeching sound coming from the drivers side of the the engine couldn’t really pin point the noise. Double checked over head and it was good. Did some searching on the forum and found another member that posted a video of the same issue after new injectors but never posted a fix. Also have the hinkling my vp is on its way out, truck cranks a good bit before it fires and it’s been getting worse over the past few weeks, raptor took a dump on me about a month ago on a trip and I …

I had to put OEM filter box back in... mice promptly moved in, trashed filter element. So today I screened the filter with aluminum expander metal & self drill / self tap screws Long ago I used SS pot scrubber behind the hood hinges... where the cowl drains are. Water drains just fine but mice can't get into the heater.