2nd Generation Dodge 24 Valve Powertrain

Hey guys, was searching around on the internet trying to see if anyone else was having the same issue I am but cant seem to find anyone with the same problem, and anyone I have talked to has no idea at all. I wish I could remember what I did when it all started, what happens is it has a little lope but its not constant, it will idle fine for a second then have a lope in the idle for a second and just keep doing that back and forth. The headlights and dash lights will flicker at the same pace as the lope. I have put an external voltage regulator, a raptor factory replacement lift pump, and a quadzilla adrenaline the one awnser I did get from a guy was that the quadzilla i…

hey guys n moparman, first post here i just got an email from the site suggesting my return but ive yet to post anyways ill start off with a bang.. 01 24v dodge excab 4x4 stock new vp n raptor, 86mph 2250 rpms i think forget what its governd to also have a 12v anywho pedal to the floorboard 13 psi going to the pump. idle i think 14 -17 im pretty sure. im trying to do this from memory i havent driven the truck in a week or so. so i believe it gets good FP? the gauge is taped into the shrader valve on the fuel intake banjo bolt and i recently changed the fuel filter and saw no change in numbers... regardless the truck gets 11-12 mpg around town. litterly $100 or…

Well anyways, my 53 block has been cracked for a couple of years now and growing steadily.Iv'e been shopping around and here is what I think I will do. my truck has 140,000 miles on itso I think the best route to take is to get a new block and have all my stuff put on it.The mech said they will do the head and do anything needed while it is in the shop. I just wanna do it once and do it right. Looking at right at 8 grand does this sound like a good number ?? I do not want to put a junkyard engine in my baby.Luke

I have a 99 5.9 24 valve 2wd, auto..... My fuel pump is not powering on anymore, when the key is placed into the on position. With the fuel heater on my "On Position voltage is around 11.8 to 12.0 volts.....it has been around 45 in the mornings here, and my grid heater/s are cycling normally. My issue is that my fuel pump only starts running when I start the engine. There is no lag time, it starts normally and the grid heaters stop cycling after about 30 seconds plus or minus. I do not have any fuel leaks and am running 17 psi at idle as soon as both fuel pressure gauges (electric and mechanical) top out about 1 second give or take after it starts...... this is not wh…

My right front axle seal is leaking and I'm wondering how to change it. I have the CAD apart and I can see myself getting the old one popped out but driving a new one in looks a little difficult. Does Dodge have a special tool to do this?

Hey guys this summer I was very proud of myself and found a 2 micron fass 150 fuel filter from my NAPA store! Little did I know it was the wrong filter I put the 2 micron for the water separator! Well in the last few days here in Minnesota it has been dropping into the low 20's and when I have been starting my truck in the morning it would run for a minute and blow the 30 amp fuse that runs the pump:shrug: So what I finally found out after calling Fass a couple of times is that my filter was drawing fuel to hard through that fine of filter, so I spun on a 14 micron Napa #3405 and hopefully all my problems are gone!

So my steering has s*cked for a long time, and the other night I took it to a mechanic I feel is pretty good and knowledgeable. He checked my truck all over in the front to see what was making it wander so bad. Poped the tie rods off, checked balls joints for play and sticking, drivers side perfect, no sticking, pass side a bit up and down but no sticking. Trak bar, universal joints in the axles, tie rod, etc all good. I have the steering brace, etc. His conclusion (he drove it also), steering box was really tight feeling and a very very small bit of play in the shaft. Bearing up in the column had no play he said.. He could find nothing else wrong so he thinks put a…

i came a cross an old thread on CF discussing pros and cons of the nv5600. the only thing unusual in it was a single post by someone stating you should only use an exhaust brake in 5th gear. no mention as to why or any responses to the post. i am just wondering if any of you have ever heard of any reason not to use an ebrake on a nv5600.

I have heard people talk about fuel millage being in the 20's and maintaining the ideal 1800 +/- rpm, but iI run down the road at 55 mph @ 1500 rpm - 70 mph @2000 in overdrive, 55mph @2000 rpm with overdrive off.In order to keep @ 1800 rpm i have to run 45 mph with overdrive off or 65 mph in overdrive.I am running 305/75/16/10 tires 32.6 in tall with 3.54 gears, would changing to 4.10 gears help. I had factory size when i purchased the truck which was 265/75/16/10 or 31.8 tall and was about the same.I am getting around 17 mpg now but diesel just hit 3.99 gal and gas went down to 3.21 gal Most of my driving is hwy, very little stop and go.I thinking of upgrading to 4 in ex…

Ok guys my truck has me stumped! Ill start from the begining and tell everything... My truck was doing the TC Lock and unlock at 45 MPH, after reading some stuff online I tried wiggling the black and white wire going from the battery to the alternator, stopped that problem I would just have to wiggle it every 3 weeks or so. The WTSL wasnt coming on either. So one morning(Months Later)I was leaving and my truck would idle fine but when I put it in gear I would have to push the throttle down like half way to get it to go, the truck felt like it had no power, it went to 3000 RPMs before it would shift, and when it did shift it felt like it was going to die. I pulled over lik…

I had bought a hot start engine heater from a buddy a year or so ago and am just now getting around to installing it. Well I am looking for ideas on how to mount it. The bracket they send you is absolute garbarge. So if any one on here has one please let me know how you mounted it. Thanks You can see a picture of the heater I here: http://hotstart.com/home/products/tank-style-engine-preheaters/small-tank-style-heaters-tps-models/

Hey guys am getting a new turbo I am planning on getting the phat shaft 62 but I am worried about the installation . How hard is it to get it on there ? Am confused on the exhaust part , since I have understood that I need a hx40 down pipe . So my question is how would I install it having the banks monster exhaust and the Banks power elbow on it ? Please if any body has any ideas and recomendations they would be very much appreciated .

How do I get the oil pan off my truck? The gasket has been leaking for a while and it's made a serious mess under there:duh: So I loosened the engine mounts and lifted the front of the engine as high as it would go. Still not enough clearance underneath to slide the pan out. What do I need to do to get it done?

can anyone tell me what these are?

Well after doing the new trubo swap .. and the 50 hp DDP injectors I have had a hard start issue . Replaced all the o ring on the injectors twice .. new injector tubes twice .. o rings on them twice . Tightened all connections , replaced the line from the filter to the VP with a big line kit . ... still air is getting back in and draining back . If the truck sits for more than 2 hrs it takes 3 cranks to start . Before it never did this with the OEM stuff . I am at my wits end . yes I searched , yes I did the baby powder , yes I parked it up hill and down hill ... If this cant be fixed I am lost . Banjo on the back of the head tight , t fitting tight . Battery's …

Still going .....Will post ALL of the :banghead::banghead: and and :cry: when I can talk about it:)

I ordered a vp44 gear puller off the snap-on truck the other day. Wondering what other tools you guys think I should pick up. I have plenty of tools. Im asking more about specialty tools I will need for working on a cummins. Thanks.

See the thread I started here - saves reposting the pics http://www.cumminsforum.com/forum/98-5-02-powertrain/441910-pdi-exhause-manifold-fitment-issue.html#post4555099 thoughts? thx --- Update to the previous post... man what a drama - cut it off and will remake a bracket later Then had the manifold back on but all 4 wholes are threaded - not like 2+2 with stocker. So 4 hours later its back off - 2 drills couldnt fix it and I had to manually file it - now its raining :banghead: Tomorrow back on - then the he351cw and some other pain

Was wondering why my 99 Cummins is SO much louder than my buddy's 07? Is it better insulation inside the newer truck or is the engine actually quieter? Thanks

I have a "minor" issue but figure I had better ask now before it gets worse. While travelling at very slow speeds through my neighborhood at the point where the trany shifts from 1st to 2nd it tends to jump back and forth from 1st to 2nd to 1st, and so on. Simply advancing or reducing the RPMs makes it quit. Any ideas? Tanks