2nd Generation Dodge Non-Powertrain

Anyone used these? [TABLE=width: 100%, align: center] [TR] [TD=width: 100, bgcolor: #BBBBBB] Part Name[/TD] [TD=bgcolor: #EAEAEA]Dodge Ram 3500 Bump Stop - Front Or Rear[/TD] [TD=bgcolor: #EAEAEA, colspan: 4, align: center] Part #S97BP60 [/TD] [/TR] [TR] [TD=bgcolor: #BBBBBB] Brand[/TD] [TD=bgcolor: #EAEAEA, colspan: 1]Skyjacker[/TD] …

When I turn my heat on it is just semi warm. I have searched the forum and checked everything. The Ac compressor kicks on and off correctly when the selector is turned. The air comes out of the appropriate vents when selected. The blend door works ( watched mopar video ) when the temp selector is turned. The big flapdoor over on the passenger side moves when the max AC is selected. The radiator was replaced and flushed 10,000 miles ago. New thermostat also. Temp gauge heats up to 190 and stays there no matter what I am doing. Both heater hoses going in from the engine side are the same temp and they are hot . I pulled the glove box and can see and feel the heater core and…

I am needing a gun rack for my 01 ext. cab. Any links or pics?

Anything wrong with this idea.Going to have a small 1 gallon tank and pump up front for my methanol injection. But I want a larger reservoir so was going to GRAVITY feed a 7 GALLON sitting in my truck bed to the front via 1/4" OD tubing .... Anything wrong with the idea ? CLICK PIC BELOWBetter ideas ?

So Friday night, we attempted to replace my ball joints. All week, I've been soaking the hub assembly and associated hardware with rust penetrate.Bottom line:Broke $1400 in Snap-On and Matco tools, and NEVER got the axle nut off, nor did we get the hub out. Afterward, we tried using the hub press tool thingy from Snap-On, where you use the hub bolts (backed out some) and use the power steering to press the hub out.. Yeah... DESTROYED the right-inner TRE; turned it into a horseshoe.. it's as if the spindle and hub are now one-piece, thanks to rust...So, I had to replace that. Never did get the hub out. I suppose next weekend, I'll just cut the ball joints , slid…

So I ordered a steering box brace from Spohn Performance. It arrived a couple days later, and I will say, seems to be a pretty class A piece.Well, it won't fit. sorta. It's the right part, and is made properly. HOWEVER, I also run a plow in the winter. The truck-side bracketry (spreader bar, torque arms, etc.) are all kinds of interfering with the installation of the new bracket... I'll investigate more this evening, and see if I can slightly 'mod' something to gain the clearance I need..Otherwise, the new steering brace will be up for sale...

Here we go again :spend: I did this http://dodgeram.org/tech/repair/elect/inst_panel_check.htm and nothing came up the oil pressure and check gauge lights keeps coming on and off all day and the fuel gauge keeps going up and down as well as the fuel light And its related to how smooth I drive ? it seems like its somewhat related to hitting potholes etc on the road unless I am just going nuts

First off I would like to say hello!!! its been a while since ive been to the site or posted anything life has been hectic! :ahhh:Now down to buisness the power door lock on my passenger side has been giving me some fits and i think its the actuator?!?! If i mess with the switch on either door it will sometimes unlock and sometimes it just wont. I called Autozone and they dont even sell one??? Is this actuator part of an assembly or just a dealer part and who out there has had the pleasure of replacing one??? Anything and all is helpful!!! thanks again.

I am preparing to install an Air Dog 100 in my truck in the morning and have to install the Draw Straw 5 in the tank as my truck had the in-tank pump installed. I spoke with Eric at Vulcan earlier today about this install, he told me to be sure to drill a hole in the side of the plastic cup at the bottom of the module, about 2"-3" up from the bottom. For the life of me I can't remember what size hole to drill. I have read the directions from Vulcan that came with the Draw Straw 5 and it doesn't mention this hole at all. In the instructions, one of the pictures shows a hole in this approximate location with an arrow pointing to it, but no explaination at all of what to…

My hood insulation is sagging badly especially in the area where my BHAF is going to be. Anyone got any ideas on how best to re-attach it? I was thinking maybe some type of glue, however, the heat might cause glue to melt. Any info will be appreciated.MOHOK

:hyper:The gear housing is just clipped together, seperate the 2 halves. Look at the orientation of the motor assembly and the remove it. My motor was "stuck". I broke it free and exercised it by hand; reassembled and I now have heat control again without spending $135!!!! Sorry; I neglected to take pictures

Hi CTD drivers,I was rotating my tires last week & noticed my front brake pads are beyond the 1/2 way point. I'm usually pulling something & she likes to work, at the moment a small 2 horse trailer & a slide in trk camper.My rotors are still good, factory style, look to me like they were updated w/ the last set of pads. I stop fine w/ what I have. I was driving w a 6x12 single axle enclosed trailer w 2 ATV's inside had to panic stop in the hills of WV, went around a blind curve downhill & my wife & I were both surprised how well it stopped. My reply was that's why I wanted a 3500 dually.I have no idea what's on there, so what are you guys using?Thanks,…

I made a trip today that's about an hour on the main highway and when I stopped I noticed my truck idling at about 900 (usually 800). Did a few errands and headed home and I got in the driveway, was idling at about i'll say 950, I shut the key off and the truck stayed running. I thought it was odd. so I went into the setting on my Edge to check to make sure the turbo cool down wasn't on. which it wasn't. Let the truck sit there for about a minute and then it shut itself down. No idea why it worked that way but more importantly, how can a person shut it down if it happens again and doesn't finally quit on it's own?

Has anyone ever hooked up an aftermarket engine temperature gauge? I know the factory gauge says 190* on the middle mark but does anyone really know what temperature the other marks are supposed to be? You go from 190* in the middle, to the next line, and then nothing until 240*. Thats a big number jump to not know whats in between.

Ok, I am revisiting this, as it is my current topic of interest.Cliff Notes:I got pulled over because I had a lens missing on my trailer, allowing "white light" to be visible. Upon further inspection, he deemed a number of other issues that 'need attention'...so, my trailer is 25' enclosed. Front has one marker light on each upper corner (forward facing) and one on each lower corner (side facing); no center lights on upper forward-facing panel.Rear has three upper-center lights but no outer upper corner lights (rear-facing.) One red each on rear lower side corners.Truck has no cab clearance lighting."Since you're in excess of 10000 lb gross weight, you need proper clea…

1998 Dodge Ram 3500 2WD 5 speed manual with the 12v cummins ( not cummings ) 149k miles regular cab 8ft PTO heil dump body with the L tool boxes behind the cab Drives well tires are maybe 10k miles old or so new exhaust clutch is strong brakes are good just got a little of a valve cover leak on the exhaust side and the oil pressure switch is gone bad it keeps going up and down and trips the check gages light horn dont work either but thats should not be a big deal to fix Doors are not rusted as well as the rocket panels it even still got the paint on it, under body is cleaner than 100's I seen before only thing rusted is the metal mounts on the bottom of th…

Hey I think it is about time to ditch the casette player and upgrade to a newer radio that may has a ipod jack and satallite radio but was wondering how difficult this swap would be. See my truck has the infinity speakers that have the big connector on them so do I need new speakers also? Thanks

I'll try to explain what I got. The first inch or so of my pedal travel is soft after the truck sits. If I pump a few time or put my foot under the pedal and pull it up I have nice firm brakes but after a few minutes it goes soft again. The pedal will return on it's own but slower than in should. I have no leaks or fluid loss although at first I thought a rear line had gone bad. I'm thinking master cylinder but I am fairly new to the hydro boost system and this started around the time I had the PS /vac pump out to rebuild the vac pump. I have not checked my rear adjustment yet but they were good not too long ago. I'd appreciate any advise. I put this on another forum and …

Okay so my map light on the passenger side has decided to stop working. The light still works but it doesn't click/ spring anymore.. Anyone have an idea of how to access/ fix it?

What are you guys doing w/ your 24V for enjoyment. I'm really pleased w/ my Dodge Cummins & really glad that I found a 3500 diesel. I'd do it all over again in a heartbeat.The guy that I bought the Sunline Camper from was using a V10 Fjord gasser & it's his daily driver too. I think that's insane. Only 8 mpg's w the camper.