Dave3500

It's nice to have fun toys! Good luck w it, Dave

:lmao2:I can laugh about it now. I called Larry from Borgeson & he told me what to to to get the SS to extend. Got it together this morning.:)Seems tighter too!Sorry wasn,t whining, I was just frustrated,Dave

I remember when I 1st started on this site Michael, you used to post about the order of mods we should do to our trucks that you recommend. Would you please state those again, or any of the knowledge that you've gleaned along the way. Thanks, Dave - - - Updated - - - Also do you have any of the pix that you are using now for the wall paper of your site. I want to check it out better, Truck & camp setup look Sweet! Dave

Me Too! - - - Updated - - - I was going to say that making to 200K that way would be more difficult!

Another Amen from the Choir!

OK I will have to check that as well guys. Thanks guys, Dave

Hi Dripley, Thanks my friend, I had 3 strikes yesterday, couldn't fix the riding mower, my Benz 300D has me scratchin my head, & now my truck is not drivable. Now I need to borrow a vehicle to drive to Louisville, Ky. Instead of fixin all my crap I should had been practicing for a recording date. Sometimes a little bit of knowledge is a terrible thing as well, or in my case just enough to get dug in too deep! So my wife has no mower cut cut grass with when I'm gone & it's growing fast! (yada yada yada!) Sorry had to vent my frustration, Dave

Overdrive hunt is where the trans is bouncing in & out of overdrive. The tack drops 100-200 RPM's. - - - Updated - - - I did a Geno's rebuild kit a few years back. Last Fall when the batteries died I but in another Alt. just to be sure. So the batt ground on the pass side it is, hope that does it! Dave

TCW3 is for 2-stroke boat or water cooled craft. You can find the stuff at Canadian Tire. Just look in the boat department. Dave Marty Feldman was cool, He was in Monty Python Flicks! Always Look On The Bright Side Of Life!

Boy this ended up being a PITA. Finally got the original SS out & it's perfectly fine, no play in the joints at all. So my replacement part is a few inches short. So for $270 plus change it's going back Is there a Different part for 4x4 or manual? I will have to make a phone call in the morning. So now I'm trying to put the original part back in & can't find any info on how to do it. A friend says to take the 3 bolts out on the column & this should give enough room to make it slide on, But I think I may have F'd up the splines on the bottom gear end..................... Seems like I can't fix anything anymore, Dave

I think I may have cut a few of them off myself, but great tips!

If there is any particles from start-up the Frantz will capture it. According to the Frantz site it's supposed to filter down to 1/10 of a micron. Dave I have one to put on my Benz just so I can extend my oil changes, 8 qts of Rotella every 5K gets expensive too! - - - Updated - - - It's sorta like the first start-up after an oil change in the Benz, it's clean but it's already black!

yup. used an Advance Auto, I thought it was going to be an afternoon job, It took my 2 1/2 days w a helper. My wife was not happy, were were going to take the truck on vacation, just make it, someone is watching out for me somewhere!

I bought some things from Thorougbred Diesel, the guys seem to know there stuff, at least the one's I've talked w over the phone.So where should a Re-man vp44 be purchased?Dave

I never replaced one, what's involved in the procedure?Thanks,Dave

Hi all,a while back I did the overdrive hunt fix & it's been doing fine for the most part. I had the trans gone through by the old-time trans specialist & it's fine but if I let it set for a few days or so I get the hunt back until it's hot. So I'm thinking I need to clean up my grounds.Anyone dune the job & have a list, pix would be even better!:thumb1:Thanks,Dave

I've got one & love it, one can tell by looking at the oil on the dipstick that even though it may be black it still clean & FULL OF LIFE!Many folks have gone 80K w oil analysis with just changing the TP!

Pumpin-cool!

True Dat!

I like the stacks!

I wonder where I can get a filter like that one? Thanks for posting that cool pic. Nice 12V!

Hi all,Just wondering if a BHAF would fit directly on the Turbo. If so, what #? I put on a fiberglass shaker style hood, like the kind that used to be on the 70 Hemi Cuda's, so it's open & a BHAF would be directly under all that fresh cool air!Thanks,Dave

OH, a 74 gasser!

Thanks got mine in the mail a few days ago, have not put them on yet. Still snowing here!!!!!!!!!!!! They look like a real quality item, thanks for pointing me in the right direction! Dave - - - Updated - - - I love the flip out feature!

They are only available in primer & do not include me year, 1998. Wonder if the plug would be different? Thanks, Dave - - - Updated - - - Would you happen to have a pic or two of you mirrors in reg & towing position? Can't tell from the ad pic if this the correct one. Thanks, Dave