2nd Generation Dodge Non-Powertrain

Steering Gear bottom domed cover seems to have cracked and leaks fluid. Truck is 175kms steering gear showed very little wear any reason why this might have happened. Can I get another cover and just replace it or are they matched? Thanks

Hey guys! I’m curious why my wait to start light is coming on with each turn if the key after it has been warmed up and driven 6 miles to work?

I decided to go through the trouble of installing a Momentary switch in the gear select arm. A Momentary switch means that it will only connect the circuit if the button is pressed. As soon as you release the button the circuit closes. IE: Pressing it will complete the Ground and trigger the Torque Converter to Lockup, as soon as you release the button the Torque converter lockup will release. This fixed the issue of forgetting that the switch was on when coming to a stop. I found that in the cases where I wanted to use the lockup switch I was already using my right hand to shift down or disable OD. It was only natural to think that a lockup switch on the Gear Sele…

I have a 95 12 valve that when I start it occasionally just my back hazards start to flash. The front ones stay off. When I press the brake the back ones stop flashing. The only way I can get the to start is by playing with (turning on and back off) my hazard switch. I was told maybe the hazards switch? Or maybe the brake switch connected to the hazards. Any ideas??

I have a 95 12 valve that when I start it occasionally just my back hazards start to flash. The front ones stay off. When I press the brake the back ones stop flashing. The only way I can get the to start is by playing with (turning on and back off) my hazard switch. I was told maybe the hazards switch? Or maybe the brake switch connected to the hazards. Any ideas??

Any one here ever made they’re own flat bed for their second gen? I’d like to do so with my truck. I need some ideas and pictures from someone that has done it!

Any advice on front bumper beginning to sag? Barely noticeable to me right now but obviously not going to get better. Anybody make support brackets or is there anything I can do?

Does anyone have any place to look for replacement pads for both the clutch and the brake pedal for our trucks? Preferably the stock ones

Is there anywhere to get the same type male and female plugs for the back-up(neutral safety) switch? To make a inline plug-in pigtail so I dont have to cut the factory harness wires to splice in a remote aftermarket back-up light on/off switch

My hinged cover is busted off my factory 7way trailer plug. Im wondering what brand the factory plug was. What brand does your factory trailer plug say on the cover? Pollak, Hopkins, or Curt or ?

I am adding a 20" light bar to my 01. I will be making a bracket to add it under my rear hitch, somewhat hidden as much as possible as it is a slim lightbar. Can I run the harness to my non main battery without ill effects? I will be running an inline fuse as well as a relay. My goal is to flip the switch on while backing up to increase my visibility while backing as my reverse lights are not bright at all. Would it work best running from my main battery?

My ABS rear axle speed sensor and my auto trans back-up light switch finally arrived from Rock Auto after TWO WEEKS ! I removed the spare tire.....Well hell,,,,,, now I can get easy access to the ABS speed sensor. Came right out.easy, didnt break off. I did not use the plug pig tail extension that was included. ABS/Brake dash lights are OFF Finally. ! .........Cool.............. I drove the left tires up on ramps so the truck was tilted. Pulled the old Back-up light switch off the auto trans. Cool , No Oil came out with the truck tilted (Yeah My Trans OIl level was full). Installed the new switch. and WaaLaa,,, My back-up lights finally…

Darn connector that holds the cables together snapped. Rolled into local NAPA store they had the clip. It's a universal clip. Part number 675-1549. Photos not uploading now but I'll post later. https://www.napaonline.com/en/p/NDP6751549

So took the battery trays out today to replace the hold down clips. In doin so I had to take off the front part of each inner fender splash shield. My question is doe anyone know the part number of the retaining push clips/plastic rivets that are used? I need about 6 of them at the moment.

Drivers side door sounds like creaky old wooden porch. I've changed a couple over the years on different cars. 2nd gens have big door. I see "doorman" brand has them. Not overly impressed with "doorman" quality, but don't know of better quality brand. Anything I should be aware of?

Ok I have been having some odd issues the last few weeks. About a year ago I got a hard CEL code P0123 and P0122. I checked for AC Noise at the Alternator and got around .03 VAC so no problems there. I swapped out the APPS for a TIMBO no problems truck runs fine. Now a year later I get a random P0122, P01693 and another code I don’t remember it was int he 300s, the last few weeks....it comes and goes usually at startup during idle. This morning I go to take the Wife last minute shopping and all of the sudden after startup I get an Air Bag Light and Brake light stuck on. Also no power to the Heater Blower Motor. Drive the truck about 10 miles or so everything else w…

I’m curious if anyone has ever bought a sound dampening hood liner? Results? Do they work? I love the sound of my truck but mainly engine noise is so loud I can’t even hear the radio.

Being "new" here and reading the multitude of elec problems...any advice on battery jumping?

Has Any one use these? https://www.amazon.com/Connectors-Sopoby-Waterproof-Automotive-Electrical/dp/B01FI6IKG6/ref=sr_1_1_sspa?s=sporting-goods&ie=UTF8&qid=1515103297&sr=1-1-spons&keywords=wire+splice+12+gauge+butt+connectors&psc=1 Ive seen the crimp kind that you can heat shrink seal after you crimp. .

Does anyone have a link to, size , the plastic fastener/clips that hold the inner front fender wells? My stocks are some kind of two piece clip I think Or is the a better fitting clip to use? Two piece removable? Mine are all loose/ rattle or missing My back fender wells I used small SS bolts because easy access to remove .