2nd Generation Dodge 24 Valve Powertrain

So latley when the temps get below 5 to -5 below, my fuel pressure is showing about 2 to sometimes 4 psi greater. It normally idles at 18 psi. now its at 20 when I first start it up and has went to 22 once. This morning I left in hurry at 6 a.m, temp at negative 6. I only let truck warm up for 10 minutes or so. temp not even registering on gauge yet. I figured Id just take it easy going down road till it started climbing. I got about 4 miles and temp was lucky to see 160 and fuel pressure was showing 22 psi. then it started dropping all the way below 10 psi. so I stopped to try to build more heat.

Alright guys I've got a vibration somewhere that I can't seem to find. It comes on at about 67mph and goes through 71. then fades up until 75 where it gets worse again. Above 80 it starts to fade. Things I've done: All new U joints, tires balanced, checked driveshaft and all weights are still there, and the rear pinion is tight. Any idea where I can look to find it??

So prey do tell how one goes about relocating the battery.

Hello y'all I have a 99 5.9l 2wd 5spd man and the crank position sensor code is being thrown. I recently replaced this with an OEM part and after a few months the code is coming back. From what I understand this issue can be caused by a loose tone ring. However, I cannot find out the exact placement despite searching multiple times and places. Is the tone ring in the block and do I have to drop the oil pan to check and tighten it? The only other thing I am finding may be an issue is the ECM itself, if that is the case I will get rid of the truck at this point. Thank you for your assistance and any insight you may have. Ed

Recently found out that I have the PTO DHD transfer case in my truck, someone told me that somehow correlates to a snow plow package from the factory?.... I have zero knowledge of how a snow plow would function on my truck. I have seen tons of plows on Craigslist...but no mention of what make/model truck they go on, which leads me to believe that they are universal. This seems rather wrong to me, lol.... SO, what does one need to do in order to set up their truck to use as a snow plow? Thanks in advance for replies and insight.

First and foremost, Merry Christmas!! Second, I don't post on this site much but absorb as much as I can from just reading the forums. I have a Fass system and yesterday and today I've been working on installing a Draw Straw 1 and 1/2 inch lines from tank to VP. Question is what do I do with the factory lines (suction and return) that were connected to the tank? I'm assuming just plug them or do nothing with them?

So I'm running winter fronts in my grill. When moving my temp is at 190 sometimes a few degrees more. But when I stop say at a light the Temps quickly drop to the low 180s. I would think they would stay at 190. I'm thinking the fan is kicking in and cooling things down. So what good is it to have the winter fronts.

so i have this app called "geek" and it has mostly chinese stuff but a lot of it is good quality nicnac stuff.. i did find a borescope for about $8 that plugs into usb and works like a champ lights and all. then i searched for a 5.5mm borescope and they have them (size we need to get into the cylinder through injector hole). So i figured id let the community know of where to get a fairly good working borescope for engine inspection for cheap!!! i w et agead and purchased the one in the pic and will do a write up on it. Mike if its possible to make this a global post so everyone sees it and can use the info please do!

Join Date: Dec 2015 Location: Wyoming Posts: 5 Thanks: 1 Thanked 0 Times in 0 Posts iTrader Score: 0 reviews WYOMING5.9ISB's Truck Pics White/Bluish Smoke Problems help.... I have a 2000 Dodge 2500 With 160k I recently am having problems with it smoking on a light acceleration until about 30mph. It stops smoking until I let of the throttle at about 60mph. then the smoke just dumps outta the pipe. I tried a hard accretion and no white smoke what so ever. Even wh…

Haven't been on the forum for a while, but I think I have a problem & could use some help. I've owned my '99 3500 dually for about 5 years now. When I first got it the lift pump/ wait to start light would energize as soon as the ignition was turned on, but after a few months sometimes (about 50-70% of the time) it would take about 5 or 6 seconds to get the pulse/light. The engine would always crank but it wouldn't light off until the lift pump pulsed. No big deal, just wait for the fuel pressure gauge to pulse then hit the key. Over the years I've read this was an indication of a problem inside the ECM (the computer on the engine block) that requires replacement to co…

Hi all, got under the truck to check the front diff for leaks today and noticed it looks like the tie rod must rub slightly at times(there is a slight scuff mark/paint free spot). Should I be concerned? If so how do I fix this?

I am looking to get a one piece drive shaft for my 01 3500 quad cab is there any shops that sell them online or will I have to get it custom made. Thanks !

My cruise control light was always staying on, but the cruise didn't work. After much problem solving, I finally took the 2001 Ram 2500 6 speed diesel to the dealer. Trust me, it wasn't my first choice. Anyway, they are telling me that the PCM doesn't know that I ever had a cruise control equipped truck. The tech claims that part of the PCM hard drive is dead. He wants to replace with new total cost of around $1200. Truck ran fine, so I'm debating how much I even want cruise control. Are there cheaper alternatives? Thanks for all the help!

UPDATE: Ok, when the head went on my truck for some reason the key was turned on a few times with a bunch of the sensors unplugged. When I had them cleared the check engine light wouldn't go out. Most of the codes went away but I still had one or two. I've had to fix so much on this truck I've been a little overwhelmed on what to do first. Everything seemed fine with that stuff so I've tackled a bunch of other things. But now I have a P0113 and P0382. The truck stalled at a stop light the other night and wouldn't start. I don't have any codes for the VP. So I don't think its that but I know its always hard to tell. This is one of those weird problems. But I don't actually…

Hello all... I was invited by Tyler to come hang out here. He said there was a great bunch of people here. Is this true??? ;-) Anyway.. Being such a newbie.. I'm not sure if I'm being paranoid. Hopefully I can explain this correctly. When I bought the truck about 6 weeks I could feel a little vibration in the steering wheel and both pedals. I attributed it to the motor and figured it was normal being a diesel. Well.. recently it seems to me to be a little more pronounced where it seems to be resonating thoughout the cab.. It happens at idle and driving any speed. It's a very fast vibration and it kind of gives a tingly feeling to my hands and foot. Does anyone know w…

Ok guys I have a 2000cummins and it was running great till today I started up a grade in 598th gear no issue till half way up it started stumbling only at 1800 rpm and up while in the throttle so I turned around and took it home and got the car and did my running well after I returned home I started it back up and it stumbled for a few min at idle and cleared up till I raved it to 3000rpm and it started stumbling and blue smoking and right befor I let off it poped in the exhaust. It also has 14 psi fuel pressure and no cel what could be causing this?

This will show the progress in installing the Holset he351ve into my 2nd gen Cummins Second Gen Cummins should be considered 94-02 but there may be some difference depending on year. I will update as I go along. This is not dealing with the controller needed for the he351ve. The thread that covers the controller can be found here The Holset He351 ve vgt turbo was found on the Cummins 6.7 L trucks on late 3rd and 4th gen dodge trucks. It is a very tough turbo and was selected for use due to the ability to improve low throttle boost and the built in Exhaust brake. It should be good for near enough to 500 hp not to matter. Parts …

Fuel Pressure Specification For Bosch VP44 Injection Pumps Here is a copy of the fuel system specifications from the Dodge Factory Service Manual. This is for your Dodge Cummins Turbo diesel truck with a Bosch VP44 injection pump. Fuel pressure Normal fuel pressure should float about 14-15 PSI running down the pavement. It should never fall below 10 PSI at all. Here is a colorize fuel pressure gauge to give you a clue of the fuel pressure span you want. You want the needle to stay in the green at all times. Yellow zone is a warning that you should check the fuel filter, lift pump performance, overflow valve, etc. This is undocumented maximum press…

I have the older style of high idle kit and the other day that I was diving and got a p0113 code. Pulled the code and found out that it was the IAT temp voltage was to high. I tired with two different code readers and couldn't clear the code. I pulled my high idle kit off and plugged the factory harness back into the sensor and was able to clear the code and have gotten the code back. Is there anyway that I would be able check to see if I have a short of some sort in my wiring or check the switches? Also from time to time I would select the 6 cylinder and then it would switch over to the 3 cylinder high idle with out me selecting it. Would like to have my high idle back u…

Hi all, I have the POSI Lock cable actuator for my 4x4. I didn't install it, it was on the truck when I bought it. I am wondering if anyone else who has one has had issues with the 4x4 indicator light coming on when its not engaged? When I bought the truck the light didn't work. I soon figured out that it just wasn't connected and fixed it. After that the light would sometimes flicker while driving, but I could usually fix it by twisting the cable until it was snug. Today the light was on but very faintly and I couldn't get it to go off. If I pulled the cable it would come on all the way, but when I pushed it in it would stay on very faintly. Later in the day I had t…