2nd Generation Dodge Non-Powertrain

Is there anywhere to get the same type male and female plugs for the back-up(neutral safety) switch? To make a inline plug-in pigtail so I dont have to cut the factory harness wires to splice in a remote aftermarket back-up light on/off switch

My hinged cover is busted off my factory 7way trailer plug. Im wondering what brand the factory plug was. What brand does your factory trailer plug say on the cover? Pollak, Hopkins, or Curt or ?

I am adding a 20" light bar to my 01. I will be making a bracket to add it under my rear hitch, somewhat hidden as much as possible as it is a slim lightbar. Can I run the harness to my non main battery without ill effects? I will be running an inline fuse as well as a relay. My goal is to flip the switch on while backing up to increase my visibility while backing as my reverse lights are not bright at all. Would it work best running from my main battery?

My ABS rear axle speed sensor and my auto trans back-up light switch finally arrived from Rock Auto after TWO WEEKS ! I removed the spare tire.....Well hell,,,,,, now I can get easy access to the ABS speed sensor. Came right out.easy, didnt break off. I did not use the plug pig tail extension that was included. ABS/Brake dash lights are OFF Finally. ! .........Cool.............. I drove the left tires up on ramps so the truck was tilted. Pulled the old Back-up light switch off the auto trans. Cool , No Oil came out with the truck tilted (Yeah My Trans OIl level was full). Installed the new switch. and WaaLaa,,, My back-up lights finally…

Darn connector that holds the cables together snapped. Rolled into local NAPA store they had the clip. It's a universal clip. Part number 675-1549. Photos not uploading now but I'll post later. https://www.napaonline.com/en/p/NDP6751549

So took the battery trays out today to replace the hold down clips. In doin so I had to take off the front part of each inner fender splash shield. My question is doe anyone know the part number of the retaining push clips/plastic rivets that are used? I need about 6 of them at the moment.

Drivers side door sounds like creaky old wooden porch. I've changed a couple over the years on different cars. 2nd gens have big door. I see "doorman" brand has them. Not overly impressed with "doorman" quality, but don't know of better quality brand. Anything I should be aware of?

Ok I have been having some odd issues the last few weeks. About a year ago I got a hard CEL code P0123 and P0122. I checked for AC Noise at the Alternator and got around .03 VAC so no problems there. I swapped out the APPS for a TIMBO no problems truck runs fine. Now a year later I get a random P0122, P01693 and another code I don’t remember it was int he 300s, the last few weeks....it comes and goes usually at startup during idle. This morning I go to take the Wife last minute shopping and all of the sudden after startup I get an Air Bag Light and Brake light stuck on. Also no power to the Heater Blower Motor. Drive the truck about 10 miles or so everything else w…

I’m curious if anyone has ever bought a sound dampening hood liner? Results? Do they work? I love the sound of my truck but mainly engine noise is so loud I can’t even hear the radio.

Being "new" here and reading the multitude of elec problems...any advice on battery jumping?

Has Any one use these? https://www.amazon.com/Connectors-Sopoby-Waterproof-Automotive-Electrical/dp/B01FI6IKG6/ref=sr_1_1_sspa?s=sporting-goods&ie=UTF8&qid=1515103297&sr=1-1-spons&keywords=wire+splice+12+gauge+butt+connectors&psc=1 Ive seen the crimp kind that you can heat shrink seal after you crimp. .

Does anyone have a link to, size , the plastic fastener/clips that hold the inner front fender wells? My stocks are some kind of two piece clip I think Or is the a better fitting clip to use? Two piece removable? Mine are all loose/ rattle or missing My back fender wells I used small SS bolts because easy access to remove .

On a automatic the Back up light switch plug has three wires, violet/blk, brn/grn, and a black/? wire. Connect the violet/blk to the brn/grn and the back up lights go on..... What does the blk/? go to? Edit, Never mind,,,,, I found it in my service manual, the third wire is the ground for the starter solenoid circuit .

Power door locks My pass side stopped unlocking a couple years ago. It would lock,down. but not unlock,up just makes a noise, eeeegh I have never took the door panel off and to check it out. Then I saw power door lock mechanisms at Geno's for about $200 ,,,geeze ! So has any one repaired a power door lock or do they just phuck up and need replacing like all the other new modern electronic crap?

Dana 60 4x4...Moog problem solvers or oem Danas? The Danas are a little cheaper for one side, about $70 and Moogs are about $90. Any input as far as quality or longevity? Because this is lengthy and annoying job, I don't want to replace them again anytime soon. Thanks

Will wheels from a 2011 3500 dually fit on a 1999 3500 dually? Cant find anything on the web regarding this. I would be going from a 16” wheel to a 17” wheel.

Hey everyone! Brand to this site. Hoping to get some answers. So my cab heater is acting up, it will blow warm to hot air through the defrost and face vents but will blow cooler air through the floor or any mix setting. Sometimes I will hear a thud or something dropping on the passenger side dash. I have a new radiator, thermostat, water pump, blend door actuator coupler (heater treater). I'm wondering if this is a vacuum or door problem, maybe even a heater core problem. Also on defrost from the driver vent to the passenger its got great air flow to almost none, so thats also a concern. Thanks!

When I hit my brakes hard all my lights and radio and everything went out and came back as soon as I let off the pedal. Does this mean electriacal short?

Im gonna add a back up light probably one of those round 35w tractor type lights unless I find a similar style 55w Where can I get a relay and what kind should I get?... auto parts store? 3 prong? Oh you can post your back up light pictures and ideas too Here's a 55w fr $32 mucho bucks https://www.summitracing.com/parts/hla-996176491/overview/

Evening Folks, I probably should have posted this up a couple of weeks ago, but it just occured to me. Im fixin to pull the HVAC box out & replace the heater core & AC core (& replace the dash & fix the EGT gauge), & figured while I had it all out I should check the vacuum pods under there. I saw from Mikes video that there is one directly on the HVAC box, but I dont know if there are other ones up under the dash (I would suspect there are as there is a bunch of vacuum lines connected together in the middle of the dash). How do you test them? apply X amount of vacuum & it should hold that for Y period of time? or is i…