I'm curious what you guys end up running for oil and filter personally I run amsoil 5-40 and amsoil filter now I'm changing to fleet guard filter LF16035

I use the same filter and Valvoline Premium Blue 15W40

Donaldson DBL7349 and Delo 400 or Rotella. Just the dino stuff.

1 minute ago, dripley said:

Donaldson DBL7349 and Delo 400 or Rotella. Just the dino stuff.

Any reason on Donaldson over the fleetguard

And coincidentally I run Donaldson and Baldwin filter setup and normally buy all my filters through Amazon

@AH64ID pointed me towards the Donaldson 3 or 4 years ago. I have a lot of trust in what he says about filters. I never compared the two.

Interesting oil and fuel filter brands seem to be less cut and dry then say s&b or afe air filters

3 minutes ago, Silverdodge said:

Interesting oil and fuel filter brands seem to be less cut and dry then say s&b or afe air filters

BHAF here.

7 minutes ago, dripley said:

BHAF here.

I want 45 PSI almost pulled one of them in so no go here

Just now, Silverdodge said:

I want 45 PSI almost pulled one of them in so no go here

32 psi is ax I see. Still running the oe HX. It does have a Banks exhaust housing and waste gate actuator. The front half is the oe part.

Ya when I put my s300 on I started noticing deforming of the filter media that was clean I took it off and have been running s&b 

Napa Gold Oil filter and either Napa oil 15w-40 or Chevron Delo 15w-40.

I run an LF3959 with Shell 15w/40

Fleet guard filter and Schaefer’s 15W-40

Mopar/Cummins or Wix oil filter, Rotella T5 oil, air filter is high flow reusable that came with twins, fuel filter is Wix stock canister...205k miles at highly enriched hp levels. 

Edited March 17, 20196 yr by Bullet

13 hours ago, Silverdodge said:

Any reason on Donaldson over the fleetguard

And coincidentally I run Donaldson and Baldwin filter setup and normally buy all my filters through Amazon

 

The Donaldson DBL7349 has better filtration and higher flow ratings than the Fleetgurad. 

 

The DBL 7349 is 100% at 20µ, 98.7% at 15µ, and 59.97% at 7µ.

 

The Fleetguard LF16035 is 100% at 30µ. 

 

The Amsoil EaO80 and DBL7349 have the same media. I run the Donaldson because it's cheaper. 

 

I have heard that Fleetguard has a NanoNet oil filter in the works, so I'll be curious to see how much better it is than the LF 16035. 

Edited March 17, 20196 yr by AH64ID

Best thing to do is ask a high mileage guy what he's running of oil and filters. Because if he made 500k, 750k or 1 million miles its a good choice of oil and filters. I'm coming up on 400k miles pretty quick. I know @dripley is nearly to 500k miles. Oh speaking of which make sure when the head comes off to snap a photo of the cylinders. I'm curious. 

8 minutes ago, Mopar1973Man said:

Best thing to do is ask a high mileage guy what he's running of oil and filters. Because if he made 500k, 750k or 1 million miles its a good choice of oil and filters. I'm coming up on 400k miles pretty quick. I know @dripley is nearly to 500k miles. Oh speaking of which make sure when the head comes off to snap a photo of the cylinders. I'm curious. 

So am I. Since putting my old RV's back in and getting the MAP sensor replaced it is running with plenty of power. I have been avoiding a full WOT run until the HG is replaced. Might throw in a new set or just have these rebuilt when the head goes back on. One of the 2.

 

Almost to 465k at the moment.

Edited March 17, 20196 yr by dripley

Napa Gold/Wix filters and whatever 15/40 is on sale. Currently using Travelers from Tractor Supply, $7.00 a gallon in 5 gallon buckets. I have 7 diesel powered vehicles, they all get the same stuff.

Usually I use a Wix in some form, either Napa or carquest and Rotella 15/40.  Although I currently have a K&N from walmart on there.

 

On 3/16/2019 at 11:21 PM, Silverdodge said:

Ya when I put my s300 on I started noticing deforming of the filter media that was clean I took it off and have been running s&b 

What about Marine bhaf, aren't they the ones have steel Mash inside. I'm a bit nervous myself now, with 7x10 and 62/67/12, I may be pretty close to pushing limits off bhaf. Maybe a chunk of PVC or corrugated/ perforated tile inside the filter will prevent it from collapsing.

Before I got my twins I had a bhaf that was high flow/reusable/washable material and wire meshed.  I still have it...got it off ebay for about $50.  Worked great just won't fit anymore.