2nd Generation Dodge 24 Valve Powertrain

Hi I recently purchased a 2001 3500 - 4x4 - 6 speed manual - quad cab. It has just under 98k miles on it. It has an edge tuner, banks 4" exhaust, Banks exhaust brake, pyrometer gauge and turbo boost gauge. It had a quite a bit of differed maintenance and a few needed repairs so I'm getting that all caught up first. The check engine light came on 2 weeks ago and I pulled P1693 + P1690. The truck was running but seemed a but sluggish at the time. I changed the fuel filter, which was really grungy. I cleared the codes and measured the fuel pressure which came in at just under 15 psi. I also changed the air filter. I drove…

Hello guys, I've been working on a 2000 5 speed truck for a friend that's got me scratching my head. Truck has just over 300k on it and was cutting out randomly and would shudder and he said it was worse when it was cold. Truck had no error codes, new fuel filter, both batteries and alternator are new. I drove it my Snap on scanner on it watching live data on a graph. I could see the APPS signal going whack when truck would act up. Had another VP truck at the house so "borrowed" good working TPS quick to verify that was the issue. Truck ran great with that factory style TPS with no issues. So I ordered the "commercial grade" APPS sensor from DieselAutoPower.com since they…

My alternator output is less when warm out than when cold. Now it’s putting out 14.3 on average. When it’s hot it’s more like 13.7. Is this an indication of trouble ahead?

Im having a difficult time finding some OEMs. I have the aftermarket cheapies on one of my trucks and they are cracking. Other truck has the OEs and are very strong. I will pay money

I have an 01 Ram 2500 5.9 that the clutch was just replaced after sitting a few months, picked it up and drove 30 plus miles no problem, next day drove 20 miles and it just quit, no sputtering or anything, just shut down. Had it towed and have checked and replaced fuel filter, bleed system, getting fuel to injectors 134. Codes, (key method)P1693 and P0122. Have electronic apps, have reset, but that should not keep from starting. Cranks strong, just will not start. maybe, fuse/relay or wire loose? any suggestions. Thanks

Replacing Diodes and Brushes in a Denso Alternator Replacing Replacing Diodes and Brushes in a Denso Alternator Remove 1the 0mm nut at the B+ post, the three 8mm nuts and the 8mm head screw. You can use a small screwdriver and gently pry and lift the cove off. The diodes and brushes are now exposed. Remove the dust cover and four screws that hold in the brush pack assembly, lift assembly out. Remove the four Philip head screws that hold the diode/rectifier bridge in, lift diode/rectifier bridge out. Remove the one screw holding the brush pack to the brush pack assembly. …

To start I have a 99, 2500, Auto, 2x4, 211,000, Lift pump in tank with Relay, 275 HP Bosch Injectors. I am the second owner & got the truck in 2001, IIRC it has 15,000 on it. To make a long story short, I just finished doing a bunch of things I have been putting off for too long now. Recently replaced (in order of installation): Vacuum pump (http://www.fixinrams.com/) PS Pump (https://www.genosgarage.com/) & Hoses (https://ormebrothers.com/). Brand new Bosch 275 HP Injectors (Had Edge Jammer Stage 1's & wanted to see the difference) ECM from https://carcomputerexchange.com/ (Lift pump was not turning o…

I finely found time to write the article about my version of the mystery switch. I hope someone with an automatic can benefit from it.

2001 Ram 2500, 5 speed, 4x4, 183k, 5.9 Cummins i was going about 50mph after driving about an hour, I got a dead pedal intermittently for about 10 seconds, then the truck died. It cranks strong, but will not start. No signs of any combustion whatsoever. Will fire off with a spray or two of ether but dies as soon as ether is burnt up. Codes: P0122, P1693, and heater grid code (can't remember the code number) Filter bowl full of fuel. Fuel filter changed about 3 weeks ago. 15 psi out of the lift pump. Swapped fuel relay. Swapped cam position sensor. Opened line out of ignition pump and have fuel when cranked. Opened line at #1 inj…

Is there a 200 degree thermostat that I can put in my 2001 24 Valve? Can you post the link to one, or a part number? The region I'm in sees temps averaging between -15 to 0 degrees Fahrenheit. Opinions are always welcome!

anyone having good luck from a parts store water pump? I am going through 1 a year and I am kinda sick of dumping coolant in the street.

I have a fairly good idea of how the lockup switch works. I am curious though, if you install a switch but don't have the switch on, will the converter lock/unlock like normal? Do you have to control it 100% of the time if you install the switch? I'm not really sure I need or want to do it, these are just questions I keep asking myself every time I see a post related to it.

Today making a drive to drop off some deer meat to be packaged, my trucks alternator voltage jumped to 18v for a couple of minutes, then went back to normal. First thing I am going to check is my grounds. If they check out to be clean and good should I put in a external voltage regulator like on the 12 valves?

Ok gang... I'm going to share a few tidbit of information for advance OBDII tinkering. If you happen to have a OBDLink or ELM327 tool you should be able to tag along here. I will have to give a bit of thanks to @Me78569 for getting me started with the Bluetooth terminal on Android. Once I had that I could directly communicate with the OBDLink and pass commands to it. So starting out I passed the command... ATSP0 This basically tells the tool to communication with the detected protocol of the vehicle ours happens to be ISO 9141-2 protocol. After that I passed the command... 0100 Which happens to be PID Mode 01 with the PID 00 which tells th…

Next weekend when I drop the trans to install a new southbend I'm installing fast coolers and a trans temp gauge also. What should be considered hot for these trans? I'm running royal purple syncromax if that makes any difference.

Ok I love the sound of my truck, it’s straight piped to a large tip and has an open air box with great turbo sound. But I have to say it, it’s too loud. So simple question, can I make it quieter without sacrificing flow? Looking maybe at muffler or dual mufflers or maybe some sort of attenuator. I daily drive and use this for normal stuff like going through a drive through or stopping to talk for a second with friends or other parents at my kids school. But I also use it like a work truck, towing and hauling campers, equipment, firewood, etc. Can anyone help with this dilemma?

Too good to be true, the truck was running good, not overheating. Last night, I saw a puddle, maybe an oil leak. I checked and after running, it is leaking a mixture of oil and antifreeze by the front case, above the oil pan. It's lost a quart, it runs fine, but the killer dowel pin is a possibility. 2001 shouldn't have a killer dowel pin? Has anyone heard of this, and is the likely source the water pump? The engine runs, so the engine seems okay. Thoughts? And thanks for the help.

Converted 2001 diesel to 5 speed no cruise cut black with white tracer The check engine light with code P1899 " P/N stuck in park or gear" then the truck would govern to 1700 RPM until code is cleared Help

Hey guys, This is my first post over here. Id like to thank Mopar1973Man for having this forum and for all the information he contributes. The trouble code walkthoughs are an amazing resource. I am trying to resolve P1689 and P0215 DTCs. Truck: 01 QCLB CTD Auto 4wd. Pertinent upgrades: FASS system 95gph, smartry and original quadzilla adrenaline. There are lots of other upgrades, but none that should relate to my question. Backround: Truck was sitting for the better part of two years. When I stopped driving it, it was running well. When I came back to start it again, I had a no crank issue that ended up being a bad ignition switch.…

fluid leaking between tcase and trans . have change seal 3 times ,cleaned surfaces, replaced with double lipped seal, still leaks yes I checked tcase seal not leaking from there. had trans rebuild after 220000 miles never leaked before rebuild. any Ideas to fix it besides sealing flanges where they mateup ?