2nd Generation Dodge 24 Valve Powertrain

Ok, So its dead from all I can tell. I want to buy a different one, should I buy a rebuilt bosch unit from my local supplier for $1150 or should I go with Jkidds are they the same pump? Should I go with the Blue Chip type X pump they suggest that it gets better gas mileage ( I tow a 3-4 car trailer and will be going a TON of miles ). I'm assuming that my truck will run better even better then it did prior to the pump dyeing due to wear etc. Is there any other options out there I'm not thinking of? I would also like to do a upgraded lift pump, maybe the fass system. I feel I'm on the right path, I'm just wondering if I should pay a little more to buy my pump from a local…

CAN YOU CLEAN OR REPLACE SOCK FILTER WITHOUT REMOVING TANK ?

Back in December my p/s fluid would foam over and while on the brakes the truck made a whining noise. I drained and refilled the fluid until it was much clearer and I haven’t had that problem since. My hope was it either was contaminated and or burnt out. Now I’m noticing a sort of soft brake pedal, if I push long and hard enough the pedal will just about hit the floor and when released it will return to normal position. I’m wondering if my hydroboost is bad or possible vac pump issue. Any help/suggestions is much appreciated. Looks like I’ll have a couple weeks of distancing from society and hopefully get this truck resolved. Thanks again.

While putting on my bhaf I noticed I do have a software update sticker on my pcm on the firewall. So is there a way to take the numbers and find out what the update was?

Upfront: I apologize for the length but I am exhausted. I am nearly convinced my 99 is too old for parts support, or I’m the ONLY one to experience a FAILED 98.5-2002 ECM. I have dedicated days and nights searching the Internet for a REBUILDER with phone follow-ups. The Internet is abound with enticing websites, pictures of pristine Integrated Circuit Boards, immaculate state-of-art facilities, complete with "experts" in uniform lab coats, headgear, and nitrate gloves peering into high powered microscopes - methodically examining/testing every component to exacting standards. Each facility promises the "perfect", “tested under all conditions”, "sleep well a…

Found this on YouTube this morning, usually just watch his videos for fun. But today I decided to look for a 47re specific one that he did and found this! Very informative video and quick tear down

dont know the fella, but follow him on instagram and he posted this. some decent info if others didnt know, some i didnt know either. really hope is continues to how he put the VP44 24v in his 1st gen truck.

I have some weird issues on my truck that come and go, First off it is a 2000 CTD, 2 wd, Automatic, 218K on the clock. I was going down the highway one evening as it was getting dusk, turned on the headlights...and the engine shut down wth? Coasted to side and tried restart no go. Turned off headlight switch and restarted fine, then found out I had no A/C or heater blower fan. Little ways down the road the fan came back on?. Weird thing is when its cool out its fine, real hot out 90's and no go. I am going to check all the battery connections and grounds this weekend, Will check codes, there was a code no comm between ECM and Injector pump I think it was? …

I see what they did but I am just not seeing how it could work to any degree of effectiveness. Can someone please "edjumacate" me please??? https://www.ebay.com/itm/Dodge-Diesel-5-9L-NV4500-NV5600-Transmissions-FAST-Coolers-PTO-Oil-Filter-Kit-/142919587199?_trksid=p2385738.m4383.l4275.c10

http://www.thehulltruth.com/trucks-trailers/506255-diesel-fuel-additives.html

, I'm in louisville ky. I have a few parts that I'll give to anyone who needs them. Front sway bar 2nd gen. Front hub spacers for a duelly Plus other parts. Also looking to sell my 01 Quad Cab 24v. Around 198xxx miles. Cummins, 4wd, fresh paint on bed, fenders, etc. Quadzilla never turned up past 3. Good solid truck. I just can't afford to keep it.

Hi I recently purchased a 2001 3500 - 4x4 - 6 speed manual - quad cab. It has just under 98k miles on it. It has an edge tuner, banks 4" exhaust, Banks exhaust brake, pyrometer gauge and turbo boost gauge. It had a quite a bit of differed maintenance and a few needed repairs so I'm getting that all caught up first. The check engine light came on 2 weeks ago and I pulled P1693 + P1690. The truck was running but seemed a but sluggish at the time. I changed the fuel filter, which was really grungy. I cleared the codes and measured the fuel pressure which came in at just under 15 psi. I also changed the air filter. I drove…

2002 Dodge 35002WD Injection pump down(VP44), Death code 216. Any suggestions for source for new pump, also what about the cam sensor

Hi, In process of servicing Cooling System, hoses, etc. I Need to replace seal on a GOOD Thermostat. Found one (1), a with Cummins rebrand for nearly $10. It's an O-Ring with grooved ID. Cummins # 3942454 Seal, D-Ring Anyone know of a better deal? Or a X-Reference. Thanks. Leaky

Hey Guys, I thought i would post this link to buy the Vacuum pump seal kit from cummins online, This company { HOESLI DIESEL in Evansville,IN} is a Cummins Authorized Service center & distributor. As you will see on there site, they stock all Dodge cummins 5.9L diesel O.E.M. parts. There was a thread on CF yesterday where a Guy was quoted one from Dodge @ 112.00++ HOESLI DIESEL: PHONE# 1-800-487-1001 OR 1-812-473-5604 hoeslidiesel.com/store/page2.html Cummins part# 4089742 vacuum pump seal kit …

I recently installed an edge insight with the expandable egt harness. I was looking at adding lift pump pressure, but by the time I buy the sensor adapter with the proprietary connector and their pressure sender I'm looking at almost $300. Has anyone found an off the shelf sender that will work with the insight? $100+ seems awful steep to me.

I'm thinking I better start looking into a clutch for my truck, and I read Mike you have the Southbend Con OFE. I'm looking at this site here in Canada and wondering did they change it that it's not called the same anymore? All I see close is the OFEK but don't want to get the wrong set up when I order. My truck a daily driver HO with the Nv5600 6spd. Have the Edge with attitude and want something that wont slip but good for daily running. Best to go clutch/pressure plate/flywheel when buying? http://www.peakdieselperformance.com/Dodge_Clutch_South_Bend_Clutch.html

Hello guys my 2001 has a been clicking sounds like the compressor but I looked and turns out guys I have a spark every so often on the harmonic balancer it comes from the rubber in between the two metals , any idea if it's a ground issue

Which way does it turn? If your looking at it from standing in front of bumper.I have done this several times and it does not want to turn.

Anyone try the Blue chip special x vp44, or have any info on them.