2nd Generation Dodge 24 Valve Powertrain

I have 98 ram 2500 5.9 24v cummins. Very new to diesels. I have no tachometer and rough downshift between 20-30 mph. I replaced tps. Cam .crank sensors. Really getting frustrated now. I have new ecm. New pcm. Please help. I have tons of money I to this truck I love it but always fix g it and don't know a lot about them . I'm getting codes for crank sensor and tps . Also my a/c blower loses power sometimes not sure if it has a short or what but I been on Google for weeks and just started forum for fist time I'm lost when come to electrical . Thank you.

Still getting to know my new to me ‘99 3500 and looked in the bellhousing inspection window today since the previous owner said it had a billet converter. Sure enough it did, but can’t tell what brand it is. It’s painted blue and I didn’t see a drain on it. No identifying marks. Does anyone have a guess as to who made it?

Hey guys I am doing the south bend dual dish 3250-5K-ORG with the 1-3/8” input shaft upgrade as well as the 5th gear retaining nut upgrade. I am all the way to the clutch for and the throw out bearing step. I read the directions and it said to replace the clutch fork with the one supplied in the kit. However it is poor quality compared to the OEM one. Will I have issues if I do not use the south bend one? I’m looking for an education on this because to me these parts look very similar.

My truck has started missing again replaced the injectors thought it was fixed. Now has a miss between 1100 and1200 RPM no load. Hàve checked the Ac noise, cleaned the grounds, removed the vanaken tuner. Have a cam sensor haven't installed it yet. Don't know where to go from here, this has been going on for a while now. No codes, any help would be appreciated. It is a 1998.5 basically stock fass DDRP 15 to 17 lbs constant

Could anyone send me a copy of the Haynes book on this model truck plz?

I have a 2001 Dodge 2500 Cummins, long story short swapped out the engine, (it's not a good thing when you suck valves down into the cylinders) an engine from a 2001 Freightliner Step Van that I put in my Dodge and now I can't get the tach to work more than 30 seconds approximately. I have tried 3 different camshaft sensors. It runs but doesn't have the power it should. Been working on this truck off and on for over a year. Frustrated in Denver.

Well today I was pulling a .. Ahem.. JETSKI out of the lake and for the life of me I could not gain traction. Pretty rediculous. Finally I used the ebrake trick to ease it out. Cmon though, a jetski! Anyway my truck performance add-ons are listed below. My question is, you think just tires are my problem? If so what are some good tires I can put on my 16" stock wheels? Or, if tires aren't it, other suggestions? Current - LT245/75R16 120/116s 1999 dodge ram 2500 5.9l Turbo diesel - Quadzilla Adrenaline Programmer - iQuad Bluetooth Guage display - hx35w turbo - boost elbow - Pusher 24V2G Aluminum Intake Manifold - S&B Cold Air Intake - Air d…

My 2001 4x4 is having an issue with the driver side front turn signal it flashes fast and very dim and the light under the hood also flashes along with it. The rear signal is nice and bright but also flashes fast. I've replaced the bulbs and nothing. I'm sure it's a ground issue but I have no idea where to even begin. HELP for the love of god!

I recently sent my ECM off to be repared. Once it was installed, there were still issues with getting it started and staying running. the ECM repair technition told me I have issues with fuel delivery. I have narrowed the problen to PDC fuse #3 (circuit A14 RD/WHT) thru the wiring harness to PDM 1 on the firewall.With everything plugged in my test light lights up when I touch #3 fuse "blade". I can unplug connecter 1 at the PCM and the light goes off. The same circuit will also branch off to the connecter and connect to the ECM wireing harnedss which powers the lift pump. I have been able to get it started but will no stay started. I think there may be an issue inside …

A little back story- i bought The truck with a bad lift pump I changed the lift pump to a raptor 150. When I went and had everything bolted up in the original location for the raptor and plugged it in and went to prime my truck I realize that the driver for the lift pump through the ECM was bad I was getting no power to my lift pump so I hardwired it to an ignition source . I knew in the back of my mind the VP was going to be close behind I anticipated the job. About 2 Months ago when the weather started getting warmer once my truck was hot it was having trouble starting it would take a few seconds to crank and then finally start so I ordered a new pump and put i…

I've seen a lot of info in this forum about engine oil but didn't run across any focused discussion on the topic. If anyone knows of one please direct me to it, if there isn't one now would be a good time for one. I'm planning to change my oil in the next few days. My local parts shop recommended Delo 400 15w40 oil and WIX XP filter (see picture) The fella at the parts shop also said something about using a thinner viscosity in winter. I do go to where it's cold but it's not exactly cold in Los Angeles. I'm hoping some of you that live in cold climates will know about this first hand. Let me know if this is the oil and fi…

I know that you guys have said that the HX35W is the turbo to get, but my HY35 has worked well for 250K. I currently have 100HP injectors, 5" exhaust, Air Dog, HBAF, and low fuel pressure light. I do not have an EGT sensor or tuner, and tow a camper and bass boat, so I am slightly worried about my EGT's, but figured the 5" exhaust would help keep those in check. SO, do I rebuild the HY35, or spend the big bucks to get a HX35W, as I can't seem to find them used with low miles. Oh the current HY35 has oil leaking on the intake side, so I am pretty sure it is toast. Thanks

What does it take to swap a 01-02 engine into a 98.5

Was working in the passenger side of the engine bay and noticed that one of the wires going to/from the PCM had been tapped. With the clamp on type that takes a male spade input. I believe it was the black with orange stripe or vice versa. Anybody know what this might indicate?

Several years ago when I changed my front diff fluid I was pretty sure I over filled and it vented some fluid and pretty much clogged the prefilter on my BAHF. Today while changing my ac compressor I could see that it has vented again. It has been near 4 years since I changed it. What would make it vent fluid now? I have a trail down the inner fender well.

Several years ago when I changed my front diff fluid I was pretty sure I over filled and it vented some fluid and pretty much clogged the prefilter on my BAHF. Today while changing my ac compressor I could see that it has vented again. It has been near 4 years since I changed it. What would make it vent fluid now? I have a trail down the inner fender well.

Several years ago when I changed my front diff fluid I was pretty sure I over filled and it vented some fluid and pretty much clogged the prefilter on my BAHF. Today while changing my ac compressor I could see that it has vented again. It has been near 4 years since I changed it. What would make it vent fluid now? I have a trail down the inner fender well.

Little background to leading up to this past week. Had the P0237 and P0112 codes with the original ECM. Replaced the MAP Sensor and IAT sensor first. Cleaned the grounds. Still had issues. Hooked it to a snap on code reader and could watch the voltage drop out to the sensors. Ordered an ECM from the number one place on the list here. Installed it. Great for 150 miles. Then got a buck and lost all throttle response. Then it came back, bucked again and then threw the P1689 code for no communication between the ECM and IP. While at the shop they went through everything using insight. Pump was dead. New pump installed. Same issue. No communication. Wiring checks out. B…

Anybody with twin turbos running and oil bypass? I pulled the trigger on an Amsoil kit but I'm running a twin setup so not sure where to get my oil feed. I've heard of people putting a t in the filter housing ports but im worried i will starve a turbo of the needed oil

(Forgive me if I asked this before) Make any difference which battery I charge up to?