2nd Generation Dodge 24 Valve Powertrain

I have 2001 dodge 2500 cummins and I keep getting this pain in the butt p0238 code. What could be the causes of this. For the other codes I've already replaced the sensors but yet they are still illuminated I'm new to the diesel life so shine some light on this problem thanks!

Looks like there’s 3 plugs on my trans. One I assume is the speed sensor which is near the back. Then there is the big sorta round plug up high pointing down and then there is one on an angle just above the pan. What is that one just above the pan? I’m dealing with my TC not u locking when it should. I unplugged the big round plug and it was still locked and stalled the engine. I unplugged the lower one above the pan and the motor wouldn’t even turn over. There’s 3 wires in that plug, one of them is very twisted up and has a bare spot.

In the middle of installing new injecotors currently. I'm curious what this buildup is on my connector tubes? How do you get it off?

Within last 3 days somebody posted about an electrail cleaner that is supposed to be really good stuff. I've searched and can't find. Anybody remember? Thanks

Trying to compare between an edge EZ, a smarty s03, and a quad but I’m not sure about it cause the guy doesn’t know what model it is because it came in a parts truck and he can’t find any switch in the cab. The box itself is sort of an odd shape but I don’t really know much about quad products to figure out what it is but based on the pics of the wiring he sent me I’m guessing it’s an xtz. Old model maybe?? Anyways truck will be a daily driver mostly stock with 50-75hp injectors and typical intake/exhaust mods at most. Just trying to figure out which one would best suit me. Leaning towards smarty but only because of the high idle..

Does anyone know how to flush out the heater exchange? I have pulled out all the tranny lines so I could replace them with the cooler, but cant find out any info on how to flush the heater exchange. I know it has a check valve, but thats it. LOL Thanks again fro the help!! /

I have not started nor driven my truck for about 6 months. She started right up but the exhaust brake in not working. I have suspicions that our dumbassed cat which has been crawling up into the engine compartment may have something to do with it. I think I have some ideas on where to start troubleshooting but it never hurts to get as much information and advice as possible before hand. Does anyone have any comments or suggestions on solving this problem. Thank!

Just had my transmission upgraded at Dynamic Transmission, LLC and wanted to give John a shout out. I was really impressed with his knowledge and expertise. Check out my youtube video on the work.

Last night on the way home I start detecting a vibration occurring when the driveline went slack. Kind of knew at that point the rear driveshaft was going to be the trouble maker. I found a way to change the rear most u-joint in under 1 hour without pulling the driveshaft. I grabbed the Harbor Freight Ball Joint Press and began to press the old joint out. Finish the job and rolled it out of the shop in under 1 hour.

My truck is mild when I bought it it had a Banks stinger package intake, exhaust, ottomind box. And has in tank lift pump. So I'm going with a Fass Td-08-095g and a sump feed is this the part number I need or should I get something else ?thanks.

When I left work today, truck worked fine. I came to a stop after exiting the interstate and when I went to go the truck seemed real sluggish. Everything felt fine once I was rolling, but moving from a dead stop the truck would smoke and slowly start rolling. Once I got closer to home I realized I had no first gear, even if I put the selector in low, it still starts in 2nd. The transmission was rebuilt by a reputable shop back in August, has maybe 10k miles and supposed to be good for 650hp. I'm not rough on my truck and haven't even towed with it yet. It does have a 3 year 100k mile warranty so I'm not worried about getting it fixed. I am curious if there is anyth…

I know there is a lot of different opinions on the internet on purchasing a billet input shaft, but I have not seen a lot posted here. What do you guys think of purchasing a billet input shaft? I am rebuilding my 47RE with a triple disc converter and a towing shift kit and were wondering if I should get a billet input for it. I am purchasing a billet flex plate also for it. My sole purpose for this 3500 4x4 is towing a 16' trailer with aluminum ladders and aluminum screen enclosures on it for mu Construction Company, which really isn't a lot for the 3500 towing capabilities. I just don't know if the shaft is needed? No I don't hot rod the truck, because its one of my com…

Background: Serviced my truck the other day and did oil change, oil filter, took off the BHAF and hit with air compressor. Went for a drive and noticed a whining sound once the boost started to build (never heard this before). Went back to the house immediately and pulled the BHAF/intake elbow and found rubber behind turbo silencer ring (see picture). I am not 100% sure where it came from. My helpful two year old could have put something in there while it was sitting on the ground, or it could have been a rubber tip that came off the air compressor attachment. Just not sure. Anyway, I ended up taking off all boots before and after intercooler to blow out/chec…

Recently I purchased a mopar1973man High idle kit for my truck. I must say I'm pretty pleased with the design and all! Id like to say thank you to @Mopar1973Man and @Me78569 for their time and investment to produce the switches. I do have a couple questions... 1. Apparently there is a delay from when you switch to high idle till the time it actually starts to high idle? 2. When switching from Off position to MPG position my truck engine skipped a beat and did a pretty good miss. Is this normal? Heres a few side notes. The only good place I could find to route the harness thru the firewall was thru the hole that the hood latch cable goes thru. But the switch would not f…

I am looking for a flex plate for my 2001 5.9 diesel 4x4 with a 47RE transmission. I really dont see the need for a billet one and are having a hard time finding a non billet one. The only one I can track down is the one on MTS website. The F2-5.9 for $195. What do yall think of this thing? Do you know of any other non billet ones? 3 Times Thicker than OEM SFI Rated Flexplate Designed to handle extreme duty applications Designed to take the punishment of high horepower engines 4mm thick centerplate Ring gears are precision robotic welded with cold welding process

Shouldn't the TC unlock when you take your foot off the accelerator pedal? While at a steady speed above 48 mph and TC locked, when I let the engine go to idle (or try to) my TC is staying locked unless I tap on the brakes fairly hard. I do have a modified VB and 3disc converter but I don't think that should matter, right?

Every new day brings a new discovery!! So today I destupided (it's the blond streaks I can't help it) and learned from this site, that I was exiting the turn key switch 3x trick do dump codes too soon, as a result I was missing out on all the fun of getting the 2nd code. I pulled 2 codes from the PCM I got a P1693 and from the ECU I got a P0230. Mind you, I was unable to pull these codes with any ODB2 scan tool. I've tried 3 different ones. I still can't pull either of those codes with and ODB2 scan tool, even with the connector disconnected. I followed these instructions and when I took off the connector, and I was super…

My heater grid is not hooked up on my truck I was wondering what are the best replacement parts to use when I put it back together. 2002 Ram Cummins

Hello I'm going to buy new injectors will my auto tranny in my 2002 be ok with the rv 275 injectors i don't miss treat it just drive to work pull small trailer if so where best place to buy bosh injectors thanks.

Does anyone know what is the wattage for our map sensors I’m guessing it would be around 1/4 to 1/6