2nd Generation Dodge 24 Valve Powertrain

Both trucks are the same. 2001 ext cab long bed 4x4 Mine is a built auto My buddys is a NV5600 We are wanting to swap each other but don't know how to go about Wireharness/pcm. The Hard parts are easy and will just swap from one to another and work fine. he is wanting to go like it came from the factory. no rachet shift no full manual valve body. any guidance is much appreciated

My 99 QCLB has 315k on it and is on the 3rd lift pump. The previous owner had the fuel pump replaced by the dealer the first time then used a big rig shop's replacement similar to the carter. So far it has been working great. The big rig shop also installed a fuel pressure dummy light which comes on only when with the wait to start is there. One of the banjo fittings on the VP44 is where the dummy light has been installed. Once the truck is running it never has come on. I mostly use the truck for hauling a little 7x12 utility trailer, camping, and pretty much any other excuse I can use to drive it. Reading through the different articles I see the first upgrade I sho…

I recently got my much needed gauges and hooked up fuel pressure first to check things out. When i bumped the starter for the 25 second run, it jumped to 24 and slowly increased all the way up to 26! Does this sound like a return line restriction? I have an adjustable overflow valve that is preset at 14 psi. What could be going on here? I think this is the cause of my rough running truck...

Hey guys, So with moving lately I've had the chance to make more long trips with my truck, and also done a good bit of lower speed back road driving. Also done a good bit of trailer towing lately. Some empty car trailer, some loaded car trailer with a tractor like in my thread about first time towing, and some loaded 6x12 enclosed trailer. Nothing too heavy, I would say 8k max and around 3k average. Anyway I've been noticing my average MPG numbers with all this driving and they aren't where I'd like them to be. Unloaded on the highway doing 65 mph with 3:54 rear, best incan get with the edge is a little under 19. With the smarty I used to have I could almost hit 22! …

I think something is wrong with my Edge... This past weekend I took a trip up to Connecticut with the camper. Under normal acceleration and driving I don't notice a problem.. but when I'm up around 65 mph and I try to accelerate up a grade I can feel the truck sputter a bit. I turned off the Edge and the problem went away. I was running the Edge on 2/3 and my Smarty is set to 2. Is the Edge starting to fail? I haven't checked for codes yet...

Just what the title says, I'm searching for anyone with a smarty (S-03) tuner in the Colorado high Rockies (I'm in Leadville, can travel) who would be willing to meet up with me and activate the high idle programming in my 01 24v so I can use my moparman high idle kit. Willing to pay cash or beer, whichever you would prefer. Also,sorry if I posted in the wrong place, wasn't sure where this applied.

Hey all, So lately I've been wanting to quite my truck down just a bit. I LOVE the sound, but I've had passengers more often lately and it gets a little annoying when trying to hold a conversation. Anyway I found a new MBRP 4" muffler on my local Craigslist for $40 and I made arrangements with the guy to buy it. He said you can see right through it but it does have some flappers or something inside. I'm concerned about my egts coming up some, but I figured for $40 what do I really have to loose? Anyway I was just curious if anyone has any good or bad experiences with MBRP mufflers that they would share with me(good or bad sound, higher egts)? Also, my truck has a ver…

Started off with finding out my heater core started to leak but the stuff should be at the house sometime within a week. But as of this morning I have know low beams but I do have high beams. So after worked stopped and picked up a new headlight switch from my local junkyard and that didn't fix it. I have checked the fuses and not really sure where to start next.

Good morning,Ok so hopefully you will be able to solve or help me solve my problem before I sell this truck! Quick background - I bought this truck about 4 months ago with 160k miles on it, it now has 170k. About a month ago I was driving down the street and it suddenly died. Pulled codes and turned out it was the injection pump, VP44 no surprise. After getting the money together, I finally had it replaced with one from Thoroughbred Diesel and also installed a FASS Titanium system while was at it. Got it back this past Monday and it was running fine. Took it on a quick 400 mile trip across FL with no issues. Then the next day I took it to work, 40 miles, and started…

Hate to bug you guys with 101 questions.......I've been using Wix airfilters for years. Last one I bought (late last year) didn't have the foam material on the back. I thought someone forgot to put it on. Today shopped for a new one at Auto zone. Again no foam backing that Wix has put on for years. Looked on Amazon and the pic has foam backing but in comments others have noticed no foam backing of what is actually shipped. https://www.amazon.com/WIX-Filters-46272-Heavy-Filter/dp/B000C9UKTU Called Wix and their FAQ people said they are no longer using the foam backing and "but what is sold today meets or exceeds OEM". I'm pretty well stock, but I do p…

Started working on my Airdog pump and low pressure fuel gauge today. Pressure tested at the Airdog port and it shows 21 ½ pounds on one of Vulcans gauges. I’ve read people like 15-17psi . I assume the psi would be the same closer to vp44. Question 1…Is 21 psi OK or is it too high and might damage pump? Model of pump is DF 100 which I think is not adjustable, but not 100% sure. The pump is mounted with the fuel line from Airdog just the way they ship it and was not cut to fit. So pump is about ½ way between VP44 and sump at tank. To take up the slack in the fuel line, the guy put a circle bend in the line under the airhorn and already chaf…

Hey guys me again. I bought a alternator after old one read to much alternator noise, well now trucks sometimes getting power to pump and sometimes just won't start , fuel lift pump kicks on but once it even attempts to start not turn over , it won't cme on for a second, not really.familiar but after all I've replaced I'm looking towards ecm telling vp not to start ? Or... I know that yall may not be able to help but thanks ahead

Hey all, As the title says I got a death wobble for the first time with this truck today. We were making the first half of the trip from old house to new and my truck was loaded to the brim with our stuff. Right about 1300 lbs worth between the cab and bed. Total weight was between 9 and 10k. I was driving south on I81 just before Syracuse doing about 65mph in 5th gear. I'm assuming I hit a bump, though I can't recall actually seeing one. Anyway it sent me into a violent death wobble. I know what it feels like because my dads old 1st gen used to do it pretty regularly. My sunflower seeds went everywhere, I had stuff falling on me from the back seat where it was stack…

Kind of an obscure question, as I was looking at the wiring diagram for my truck. (see link) @Dynamic If you have any input here... I would appreciate it. I am trying to figure out why the trans relay is in line with the alternator field. If you look at the PCM on the left side, about mid way down you will see a GEN FIELD DRV, in dark green. This field runs 100hz AC to the alternator from the PCM causing it to charge. Lower you will see a GEN FIELD OUT, returning from the alternator to the transmission relay. Why would they do this? Why not run the signal for the trans relay directly to the relay? Why allow the non steady state voltage reg…

You guys say i need a fuel pump relay. I buy a new relay and understand all the wiring to it. Crawl under the truck and find 2 wires going to my fuel pump. ! red and 1 black. OK find the ground. Use ohm meter, both go to ground. Fire the truck up and red reads 13.9 and black reads .3. Check black with ohm meter and it does not show ground. ?Probable goes to ground through computer?? Do not want to screw anything up! HELP?

I've gathered parts I need for low fuel pressure gauge. Some parts from Geno's, some Vulcan, some local store. Have a mixed metals in fittings... I have NPT, alum and brass metals. Some with flare some without. Thread locker question... Teflon tape? pipe dope? Removable thread locker? What is your favorite thread locker.

@Mopar1973Man please put this up top for me. If you think it should be somewhere else, go ahead and move it. My truck was stolen last night in lakewood. I'm sure most of you know what it looks like, but here's a couple pictures. One of the passenger windows was busted out to gain access, but I have no idea how they got it running. Thank you

My Son`s 2000, 3500 has had some erratic transmission behavior going on for a little while. It seems like a the familiar TC lock/ unlock issue.. At lower speeds and rpm it continually searches. Turn the overdrive off and the issue goes away. He pulled the alternator fuse and took it for a test drive and the issue also went away. Now fast forward. He bought what I believe was a remanufactured alternator from Oreilly`s last week, and everything seemed great for a few days. The trans symptoms have now came back intermittently, and on top of that, the new alternator is now making a slight squealing noise like the belt is slipping a bit. Oreilly`s offered to s…

Beginners question... The bolt that holds the fuel line to the VP44. What is the torque when I put it back in? The bolt must be hollow, I don’t want to do any damage. Any thing else I need to know? Thanks

New member here. I notice Dynamic Transmission is one of the sponsors of this forum. I see hardly any posts about peoples experience working with them. Anybody here have one of their transmissions? How do you like it? Any info good or bad would be appreciated.