2nd Generation Dodge 24 Valve Powertrain

First off, Merry Christmas, second off I would like to say thank you to TFAORO for helping me get the truck running while off grid in -10 degrees Fahrenheit I had a 10 mile ride on a wheeler just to get a form of cell reception then for Tyler to respond quickly was awesome . So long short this is her first winter back on road 99 24 valve 5.9 4x4 auto with 320k on the clock basic mods and hybrid turbo, full frame off restoration... because of that I'm not ruling anything out yet. The facts Outside temp was -10 dropping to -14f blowing 20mph Truck was plugged in on generator power for 6 hours tested for good voltage to find it present...…

is it possible to remove the sending unit without removing the fuel tank?I want to see how much of a job it is to increase the fuel suction lines.

Hi, I have a DANA 80 with Limited Slip Differential that I’m draining/changing fluid in. How many oz. of additive do I need for a complete oil change please? Thanks Leaky

Has anyone installed RV275 injectors in an otherwise STOCK or very lightly modified truck and ran it on a dyno? Anyone made dyno pulls mostly stock vs 275 injectors? I have a 01 4wd auto. Bought it cheap with 174xxx miles needing some minor work. The only engine upgrades are a BHAF, a Fuel Boss pump and new Bosch RV275 injectors. Truck runs much smoother with better starting after the injector swap but I'm curious how much HP and TQ the injectors really add.

I am thinking about picking up some injectors. Anyone have experience with DAP Aftermarket injectors? Here's what I'm looking at. Obviously I'm looking for a lower cost Injectors, I have stock now. I'm running a 150gph pump, turbo upgrade is after the injectors. Set of 6 Diesel Auto Power 125HP Aftermarket Performance Injectors for Dodge 24 valve Cummins. 7 hole (0.0095 inch holes) SAC style. Compatible for years 1998.5-2002. Installation kit included: (Injector connecting tube removal tool/nut, copper sealing washers, and o-rings for connector tube). new copper washers

Recently I became the owner of a 26' gooseneck flatbed trailer. Its awesome having such a piece of equipment. I can haul multiple pallets of pellets home from the store at once, haul the tractor around for side jobs etc. The heaviest load I have towed is 4 tons of pellets for our pellet stoves in our home. 8K pounds plus my truck that weighs 7100 plus the trailer I'm guessing is around 2,500 or so. Just rounding up to 18K pounds...my truck did "OK" up the grades. Steepest grade to pull going home was 5% for 2 miles. Started out at 65mph at the bottom and was barely doing 35 at the top. If I go with twin turbos it would purely and solely be for the added power for …

What's the normal time to change injectors for those of you who do it all the time? Yesterday I changed injectors, set valve lash, and installed a Vulcan banjo bolt eliminator kit from filter to block mounted pump. Took about nine hours, though had Dirty Jobs and Strange Inheritance on in the background to distract me a few times.

I just want to see if I can clear the air up a bit on a few things and talk Cummins related additives From what I understood, in the past Cummins had never officially endorsed a specific additive nor advised using one. I believe they stated that as long as you were using adequate fuel, there was no need, unless you needed protection from gelling or worried there was a lot of water in the fuel for some reason. A lot of people seemed to think that Cummins endorsed stanadyne, but from what I've read, it seems that it was a misunderstanding. A person closely related or that worked for Cummins said that he really liked stanadyne or said some great things about it a…

got a airdog original pump on the truck right now and been looking at the Fuel Boss Mechanical Lift Pump System. I was wondering if anyone has had put one on yet? I want to use the airdog filter setup up on it, if it is possible or do I need to buy a different filter set up for it? Would really like it better then the airdog because im sick of messing around with the airdog and would like to have something that is really reliable. If anyone knows someone I can talk to on making the fuel boss work with the airdog filter setup that would be awesome thanks guys.

Does anyone know where I can get new trans cooler lines from the transmission up to the heat exchanger tank or whatever that tank is on the side of the trans? Its leaking really bad out of that fitting.

Other than the governor sensor in the transmission, is there another way that this code could be set, (P1763)?? :confused: BD-VB HAS BEEN REPLACED, GOVERNOR RELAY, GOVERNOR SENSOR, VB HARNESS, 100 OHM RESISTER ON THE ORANGE WIRE UP BY THE PCM, ALL HAVE BEEN REPLACED. EVEN THE SPOLL VALVE and SIGNAL MODIFIER BOARD ON THE PRESSURELOC. I've EVEN HAD THE PCM RE-FLASHED TO NOW HELP.I have a 2001 Dodge RAM 3500, Dually, 5.9L, Mods:BD: FLEX PLATE, TORQ CONV, TRANNY RATED AT 450+HP, PRESSURELOC, TWINS, 130 INJ, X-MONITOR, and STEALTH COVER. BANKS FOUR INCH EXHAUST.AFE COLD AIR INTAKE, THAT CAME WITH THE TWINS.EDGE J/A.ALL THE APROPRATE GAUGES. KELDERMAN 4LINK 2 AIRBAG.VERY NICE …

I just got my S-03 smarty. I've read through the manual and have an idea on how to use it. However, the manual don't tell me how to just turn on the high idle in the stock ECM program. When I load a catcher program (they all have high idle enabled in them) to the ECM, the smarty stores much of the original ECM program and then vin locks so It can't be used on another truck. I can restore the original program to my truck and then the smarty unlocks so it can be used on another truck. So my question is when the original program is restored to the ECM is the high idle turned off or left on in the ECM? There is no specific function in the smarty to turn on the…

Hello guys, haven't been on in a while but now that the house repairs are done for a few months I thought I would do some things to my 2000 CTD. I am thinking of getting a performance tuner and this will hopefully not open a big can of worms and arguments, not my intention. I have a 2000 Dodge CTD that is stock with the exception of a 4 inch exhaust. Thinking about installing a exhaust brake for towing our travel trailer. I am also thinking about installing an engine tuner and am looking for ideas and suggestions on which one to get. I'm looking at the Edge tuners. Any thoughts? I don't want to install any high flow injectors or a high performance Injector pumps…

So this started just after I got the truck home. I moved from one driveway to an other and the engine stopped. Restarted moved and stopped. Then ran fine. Week later and 1,000 miles into my get to know each other trip and the truck starts hick upping on the freeway going through Portland after 3 hours of driving. Did it for 7 - 8 times, not in conjunction of the bumps in the road or anything. So we are a week later and it starts hic-cuping on the way to Ace. Engine just dies then runs again. 17 PSI on the FASS to the VP. No Water in the Water Trap. Does it for 8-10 times. Just like you bumped the switch off then on again. I've seen things about dat…

Is there any way to adjust the shift points on a 47re trans? I've thought it would be nice for towing if it would shift sooner and tonight just for kicks i did a couple 0-60 runs and it badly needs to shift sooner for that. It took 10 seconds to hit 60:doh:

What would be the best turbo for a 2001 ho six speed with 100hp ddp injectors

Anyone know why I would have my power steering fluid overflowing? All was fine for 3 weeks without driving it (Driveway statue) and then one hot day it's coming out the cap. With truck sitting idle for 3 weeks, suddenly the fluid is at the top and overflowing.

HI, MY TRUCK JUST STARTED TAKING LONGER TO START, I HAPPENS EVERY 1 OUT OF 3 TIMES I START HER UP. JUST REPLACED AIRDOG FILTER AND SEPARATOR, AIRFILTER, PURGED SYSTEM AND IS STILL DOING THE SAME. HAVE ABOUT 40K ON A NEW VP44 AND NEVER HAD ANY PROBLEMS. FUEL PRESSURE READING IS 17PSI AT IDLE AND 15PSI AT WOT. IF FEELS LIKE ITS GETTING AIR IN THE SYSTEM, IT TAKES ABOUT 5-10 SECONDS TO START AND WHEN IT DOES IT AUTO-ACCELERATES. ANY BODY FAMILIAR WITH THESE ISSUES???

@Dynamic This one is seeking your advice. I can't afford one of your valve bodies or a converter right now so its time for a shift kit. Transmission was rebuilt to factory specs by Cottman Transmission about 25,000 miles ago, before i bought it. Works fine, no slipping or other issues. I use it for a daily driver with occasional hauling/towing, max load of 10,000lbs. I have installed Sonnax accumulator piston, second gear super servo, billet band strut and anchor, Rostra transducer & OD/TC solenoids, Borg Warner pressure solenoid, LPW deep pan, and adjusted bands and TV cable. I do not like how these transmissions shift. To me they shift too soft. I like a trans that …

SO as some of you may have seen, I bought a new truck, 2000 with a 47re, problem is it only goes backwards! So here's the story: Kid I bought it from bought it about a year ago from the original owner to, and I quote, "to roll coal and do burnouts" and he did just that, and it took the tranny with it... kinda. It started out he said slipping a bit, so do what most people would do when they're trying to sell their truck and tranny starts slipping, burnouts! Couple burnouts later it wouldnt go above 25mph, so he took it to a buddies and they put more atf in it, I don't know why, and magically it doesn't move forward any after they did that, and here I sit. …