2nd Generation Dodge 24 Valve Powertrain

hey i know this has topic has popped up heaps of times though im running out of ideas on mine 1999 cummins converted to right hand drive , i have replaced both ecm and pcm with remans from auto computer exchange, replaced transmission sensors solenoids.. speedo sensor on diff with new 5mm wires overkill i know, up to plug behind left wheel ive had all harness on engine stripped when i was diagnosing ecm issue, just recently was when i changed the pcm hoping that'd be the overdrive issue prior to that i had the switch on the dash mod so i know the transmission itself isn't the issue i spliced into wire for the o/d at the pcm so i know the wiring down from there is ok and i…

Well we all know what this code means. I have been fiddling around under the hood a lot lately and I wonder if I bumped something that could cause the code? Truck still runs ok but seems like it got a bit louder as far as the typical knocking noise. Is they’re any other symptoms that show with this code? I honestly hope I have to do a vp because that could be cuasing a few small issues of been having for a while....

Good afternoon everyone, This past week my vehicle situation has changed and I have been driving my 99 daily. Since I have not driven it much this winter in the cold I don't think it sounds right. I can hear a knock or a rattle noise when driving it and think it is either a fuel knock or timing knock and hopefully not something else. The noise does not increase with rpms, but it is there. I believe the injectors are stock with 174k miles and the truck has a Quadzilla XZT+ chip. Both videos were taken with the chip in the "timing" setting. I have turned the chip to the off setting, the noise is there but faint. I have included a couple video clips, what …

Been lurking the forum forever but haven't posted much because I can usually find the answer. Anyways, I just bought a Frankenstein 99 Dodge that's p-pumped, with a G56 transmission. It also has an S363 turbo with 70 hp injectors, and it's leveled on 35x20's. Someone has spent a significant amount of time and money upgrading this truck, but it also came with a lot of issues. (I might add that the body and paint on the truck is 9/10, only 1 noticeable dent.) For instance, the front end is loose as hell, but the truck came with all the parts to do a front end rebuild. The dash is busted all to hell, the AC doesn't work at all, the gauge cluster doesn't funct…

I recently performed my first rotor swap on my 98.5 2500. I pounded out the wheel studs with a single hit of a 5lb sledge. Easily came out. I swapped the wheel bearing assy over to the new rotors. Used same sledge to set the studs back in the same wheel bearing housing. A few studs did not want to set back in place flush. I whacked ‘em a few times and carried on. Thinking I’d pull ‘em right thru when I torqued the lug nuts up at wheel installation. Well I’m still cranking a few nuts tight. I’ve been test driving and get a slight vibration when braking. I have driven, braked and got hubs warm, then retorqued 3X. Seems I am almost there as the vibration is imp…

As I have a 3500 4x4 gas truck sitting not being used and a fair way from being able to be used I'm thinking about breaking it for parts (need the space) what is the difference between a 46RE and a 47RE, trans on the cummins should really be done so I was thinking would it be possible to do the 46 to like dynamics stage 3 trans and its then a 47 ? Or am I missing something. Just read that the trans are basically the same just higher torque rating on the higher 2nd number. Would do the full works think it works out to around 5k. Importing a done trans isn't really feasable due to taxes and shipping charges and core charge

I still have my TC lock up issue so this morning I thought I would check my apps voltages. 0.314 at idle climbs perfectly but max voltage is 3.46 at 100% throttle I believe this is too low?? The quad is showing 100% throttle. Any input would be greatly appreciated guys

My cruise control light was always staying on, but the fly-by-wire cruise didn't work. After much problem solving, I finally took the 2001.5 Ram 2500 6 speed diesel to the dealer. Trust me, it wasn't my first choice. Anyway, they told me that the PCM didn't know that I ever had a cruise control equipped truck. The tech claimed that part of the PCM hard drive was dead. The dealership ordered a PCM, but somewhere along the line there was a mistake and they received a PCM for an automatic transmission. They didn't install it. Instead, I ordered a PCM from NAPA for about $450. The PCM came in and the dealership agreed to install it, labor free, since they'd scre…

I drove the truck for the first time in 4 weeks and started getting a no 2-3 up shift condition. It will up shift when backing off the accelerator. All the other shift points are at the proper speed/throttle position. The transmission speed sensor was replaced 8/8/18 (107,893mi) due to no 1-2 up shift but would start off in 3ed if transmission relay was pulled. Transmission was serviced with front and rear band adjustment 9/1/18 (108,024) then a 1,000mi trip in October pulling the 5er with no problems. The transmission now has 109,362mi. I'm thinking it may be the governor pressure sensor and solenoid. They were replaced about 45k mile …

I am wondering if I can tweak something in my tuning to give me a little more power on hills. If I am running 55 up a decent grade it's like it's stuck between wanting to down shift and just not having the power to pick up the speed I want it too. Kinda hard to explain so I hope I make some sense. I know some bigger injectors and turbo would help more than anything.

Hey guys. So I went to get in my truck this morning for work, and noticed a small wet spot on the ground next to my passenger tire. Thought maybe the powersteering pump fluid made it's way over there since it's currently leaking, but it is coming right from the housing. How complicated is it to take it apart and replace the seal? Any special tools? Should I replace anything else while I'm at it? On another note, I've been noticing a slackness in my steering. It's not the wondering steering, it's like I turn my wheels a direction and it almost snaps back a little like there is some sort of play in the steering somewhere. It's not harsh, it just feels loose…

I have ended up with a 71/71/15 non wastegated t4 k29 borgwarner turbo. Anyone on here ever run one? I assume it's to small to run in a compound set up. But I'm wondering how it would run as a single ? Truck is purely a street truck that gets used on weekends I dont ever tow with my truck maybe once or twice a year only light loads.

Awhile back I posted wondering if a VTSS system that I didn't think I have could be causing a no start , and no 25 sec LP run that I was experiencing occasionally , I got no response . This no start was happening it seemed after the bats were disconnected for a few days while doing other things to the truck , and then it would run again. I had just replaced the ECM so I wondered if it was causing the problem , but the WTS was working ,LP 2 sec run with key to run worked and the cluster was also , when it ran it was fine , no codes , tach was not misbehaving So it happened again after the truck had been sitting for a few days - bats where still…

So I've been having difficulty finding the proper oil and I think I have the correct stuff but I want some input before I drain the old oil. So it started at NAPA I asked for the transmission oil for my NV4500 in my 1999 ram 2500. The oil I was given was part number 04874464ab. I immediately found this fishy as on the front of the bottle is says for the NV3500 and NSG-370. I got NAPA to call back the dealer that they got it from and they insisted that this is the correct oil. I did some research online and could find nothing to this being a replacement for the syntorque oil that is discontinued. After this I caĺled Castrol directly and told this what I had and what oil I …

Couple days ago i removed the "air inlet tube", the big hose from air filter box to the turbo. The hose has particles I've never seen before. Wix filter only has about 2800 miles on it. Many miles from the maintenance schedule "light duty "B" of "inspect/replace every 15,000 miles". Folding air filter in half, I can see semi loose strands bewteen the pleats waiting to be sucked in. About same size of 3 days of no shaving. Never noticed it before... Is this normal?

This week I've had a few times where I'm doing around 65mph on the highway and I hit the pedal to accelerate, and nothing happens. The engine sound might change a tiny bit but I can't accelerate at all. if I mash or get off the pedal and back on it doesn't let me go any faster. Quadzilla doesn't show anything strange, except that my throttle position changes with the pedal push. If I downshift for a sec and then go back into 6th everything is fine. Today I pulled the codes for the first time and got P0216. I'll have to check and see if it comes back. There was one odd thing 2 weeks ago when I changed the fuel filter, the next day it took about 6s to start vs the near inst…

01 2500 auto with a hx40....150 over injectors....adrenaline on level 3....3 piece bd manifold....running 80 on the interstate I’m getting 1000 with a little wind but not even towing anything...seems a little high?

Maybe a stupid question but I’m having trouble finding non-conflicting information. I know the PowerMax is a fuel only box. I am trying to figure out if a box for an 01-02 can work on a 98-00 truck. I know the MAP sensors are different (plug and voltage values). I have read some info saying that unlike EDGE the PowerMax box will work on all years with a MAP adapter harness. Can anyone here confirm or deny this information? I have tried to contact TST but they are closed until Monday.

Is there a way to tell which Denso diode I need... by looking at the alt is still hooked up? Like maybe that threaded bolt coming out is in different spot?

Hi All, my truck has recently presented a new issue. The oil pressure reads rather high, mostly all the time on the gauge on the dash. I'm thinking the oil pressure sensor could be failing, but I would rather make sure my oil pressure is correct. The bad news is I'm about 200 miles away from home for the next week and don't have my service manual with me (doh!). The good news is I have access to tools so I may be able to solve this while I'm here. I have a mechanical oil pressure gauge and was thinking about testing the pressure first before making assumptions, does anyone know if anyone posted an article about how to prope…